Jump to content
SAU Community

Recommended Posts

When people say the Michelin Pilots are great or bad, are they talking about the Michelin Pilots Sports, or Michelin Pilot Preceda?

And has anyone has experience with the Avon brand of tyres? I see on www.tirerack.com that the Avon Tech M550 A/S "beat" every other brand of tire (ultra performance, all seasons category).

I have Ziex 326 and wanna upgrade to much better ($300-450/corner) tyres, as I'm sick of spinning the wheels in 1st, then 2nd and even third from the lights without even trying! Not even modified either, just exhaust :) Wear isn't so much an issue as I only do about 15K kms a year and it's mostly city driving with the ocassional coast trip (which is all highway anyway, no off road).

haha anything will be better than 326s!

I back falken fk451 or dunlop sp9000, they are both excellent road tyres, but depending on size they are up to 500 per corner.

OK. but didn't really answer the question...

Michelin Preceda or Toyo T1-R will cost me a bit over 400 a corner and lots of ppl have been talking about them so immediately they are ahead compared to any $500 tyre. 1600 i can *kinda* justify, but definitely not 2 grand.

Then again, this site with the Wheels test: http://www.aussiefrogs.com/forum/printthread.php?t=23777

says there is less than 5% difference between all the tyres in the test (5% in what I wonder.. too vague). Anyway, I have just seen the Maxxis Victra MA-V1 in 235/45 R18 for only 209 each @ Bob Janes.. so the Maxxis Victra MA-Z1 couldn't be a whole lot more (even if it was 100 more, that's still only 300 a corner). I would expect about 250-260 each.

Has anyone had experience with these tyres that are supposed to provide comparable performance to several 350-400 buck tyres? Apparently my Falken 326's cost about 200 each.. I find it kinda hard to believe the Maxxis could do so well for so cheap, so I really wanna hear from anyone who has them (and has owned enough tyres to compare fairly).

what size rims rice, the new fedrels are not to bad i have some on the rear, and after the first few weeks they have settled in very well, little spin in first then nothing but hook up in second.

r33 gtst 216rwkw 18 /265/35 the new ones have a lot more silica in them, so before ppl go baggin them there different now

!!! RICE?! ri*N*cewind :P man.. hope most ppl aren't reading it that way lol uh nevermind :) Those who know, know.

Rim size is 235/45 R18. I dunno about the width.. how can u tell by looking? I didn't put them on myself so I dunno.

Quickfit just 5hat on Maxxis from a fair height.. saying they are a long wearing budget tyre (about 40k's instead of 25-30k), that they sacrifice on grip, and that Wheels is a biased magazine and the next magazine on the rack will push some other tyre make/model. He also said that they don't have much experience with them though.

Grr

had falken 326's on the rear... and they were ok in the dry and just death in the wet.. anyways after spinning out just the other day.. i put my foot down and decided to ditch the falkens as they were ABSOLUTE rubbish

replaced them with the same size (245/40/R18) as before but toyo TPG's

paid $540 fitted for the two

and they have worked out allright.. i wouldnt say they are fantastic... but as an upgrade on the falkens they are damn good.. i wanted t1-r's... but found out how expensive they were

i give the toyo tpg's a wet: 6.5/10 and dry 8/10

value for money would get a 8/10

I just got quoted 250 a corner for Maxxis MA-Z1. I can't go past that, seeing how well they did in the magazine road tests (I heard Motor gave them a good review too), for 1K as opposed to 1600, the decision is now all but made!

The fitter said the reason they are so cheap in Australia is cos they've only been in the car tyre market here for about 2.5 years. My mechanic also says they're great, so I'll give em a go.

I just got (after recommendations in this thread) Hankook K104s... unreal tyres, I got:

-255 * 40 * 17 (rears, 9 inch rims)

-235 * 45 * 17 (fronts, 8 inch rims)

Very sticky at the moment... I have a stockish R33 GTS-T, and full throttle out of most corners I have problems spinning them at all, lol, and the rear end is very very stable. Wet weather driving is great too. But coming from Falken Ziex 326s, anything is a huge step up.

Will report back in ~10,000kms anyway.

since they wieght of all skylines are in the 1300 - 1600kg range I reckon the recommendations are pretty relevant. Suspension mods make much more difference to tyre performance that power.

Unless you mean rear traction problems out of big power cars?

Either way, if you buy a sports car, modified or not, buy the best tyres you can afford for it, they make more difference to performance than any other mod.

I had the Toyo T1R for almost 2 weeks which I put them in the front (235/40/18) and in the wet holding is pretty good plus confirdent. Dry is excellent. I am waiting for my rear sets next week (265/35/18). I was told it's better than Yokohama AD07 in the long term usage. You guys reckon it's true?

haha yeah Snowman knows the deal, not that it matters now :P

rincewind was better! LOL

I actually tried to get the personal plates BINKY in Vic but they were taken already.

Anyways.....

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
    • But first....while I was there, I also swapped across the centre console box for the other style where the AV inputs don't intrude into the (very limited !) space.  Part# was 96926-4GA0A, 284H3-4GA0B, 284H3-4GA0A. (I've already swapped the top 12v socket for a USB bulkhead in this pic, it fit the hole without modification:) Comparison of the 2: Basically to do the console you need to remove the DS and PS side console trim (they slide up and back, held in by clips only) Then remove the back half of the console top trim with the cupholders, pops up, all clips again but be careful at the front as it is pretty flimsy. Then slide the shifter boot down, remove the spring clip, loose it forever somewhere in the car the pull the shift knob off. Remove the tiny plastic piece on DS near "P" and use something thin and long (most screwdrivers won't fit) to push down the interlock and put the shifter down in D for space. There is one screw at the front, then the shifter surround and ashtray lift up. There are 3 or 4 plugs underneath and it is off. Next is the rear cover of the centre console; you need to open the console lid, pop off the trim covering the lid hinge and undo the 2rd screw from the driver's side (the rest all need to come out later so you can do them all now and remove the lid) Then the rear cover unclips (6 clips), start at the top with a trim tool pulling backwards. Once it is off there are 2 screws facing rearwards to remove (need a short phillips for these) and you are done with the rear of the console. There are 4 plugs at the A/V box to unclip Then there are 2 screws at the front of the console, and 2 clips (pull up and back) and the console will come out.
×
×
  • Create New...