Jump to content
SAU Community

Recommended Posts

Exhaust sounds great, nice rumble on idle and not too loud up top. Will see what it sounds like when front and dumps are swapped out. Uploaded a video clip of exhaust sound on YouTube

Can't seem to attach it here.

  • Like 1

Exhaust sounds great, nice rumble on idle and not too loud up top. Will see what it sounds like when front and dumps are swapped out. Uploaded a video clip of exhaust sound on YouTube

Can't seem to attach it here.

That does sound great mate.

After 3 years I finally re-installed the tailgate linings on the 25g and the RS4. I had tried to fit an electric tailgate closer to the 25G but could not get it to work.

Tomoz I start on the electrics or the RS4. Air con condensor fan needs rewiring, dash panel to be replaced and A/M gauge cluster lights need fixing.

They say a dying candle burns brightestLOL

found the issue to all my problems yesterday

DSC_0138.jpg

water damage in the oem to f-con harness.

spent a solid few hours giving it a clean with contact cleaner and earbuds.

Gave the ecu a reset and in for the first time in months i have clear dash with no engine light :yes:

And also scored a HKS F-con Navigator pro , which i installed at the same time

DSC_0145.jpg

Edited by Footo
  • Like 1

found the issue to all my problems yesterday

DSC_0138.jpg

water damage in the oem to f-con harness.

spent a solid few hours giving it a clean with contact cleaner and earbuds.

Gave the ecu a reset and in for the first time in months i have clear dash with no engine light :yes:

And also scored a HKS F-con Navigator pro , which i installed at the same time

DSC_0145.jpg

What does it do? Give you info or can you make changes to your tune?

After 3 years I finally re-installed the tailgate linings on the 25g and the RS4. I had tried to fit an electric tailgate closer to the 25G but could not get it to work.

Tomoz I start on the electrics or the RS4. Air con condensor fan needs rewiring, dash panel to be replaced and A/M gauge cluster lights need fixing.

They say a dying candle burns brightestLOL

25g? Damn I've always wanted the auto tailgate.

Did the timing belt (turns out it is from a Volkswagon Passat), water pump, cam and oil pump seals, idler and tensioner bearings for the second time (the engine has about 180,000klm on it now). It does use a bit of oil by now, the head in particular was not reco-ed when the rb30 was built so it has 300,000klm+ on it.

Then loaded the kids into the back took it for a leisurely drive up to queensland for a week away. It's thirsty and noisey with that exhaust, but it didn't miss a beat all trip

Did the timing belt (turns out it is from a Volkswagon Passat), water pump, cam and oil pump seals, idler and tensioner bearings for the second time (the engine has about 180,000klm on it now). It does use a bit of oil by now, the head in particular was not reco-ed when the rb30 was built so it has 300,000klm+ on it.

Then loaded the kids into the back took it for a leisurely drive up to queensland for a week away. It's thirsty and noisey with that exhaust, but it didn't miss a beat all trip

Did you get to Mt Tamborine??

25g? Damn I've always wanted the auto tailgate.

Where the harness comes into the tailgate on the RHS there is a feed wire missing going into the loom. I dont know where this feed wire comes from.

Would love to get a wiring diagram.

Where the harness comes into the tailgate on the RHS there is a feed wire missing going into the loom. I dont know where this feed wire comes from.

Would love to get a wiring diagram.

I've been trying to find it again... I found a workshop manual on yahooauctions. I think there is one in someone's Dropbox?

Shouldn't be too hard to decode if you start with the headings and work your way down.

Did you get to Mt Tamborine??

actually I took poetic license because I only made it to murwullimbah/tweed heads (figured that was close enough :P)

but i'll call you for a beer next time I'm in town :)

found the issue to all my problems yesterday

DSC_0138.jpg

water damage in the oem to f-con harness.

spent a solid few hours giving it a clean with contact cleaner and earbuds.

Gave the ecu a reset and in for the first time in months i have clear dash with no engine light :yes:

And also scored a HKS F-con Navigator pro , which i installed at the same time

DSC_0145.jpg

What does it do? Give you info or can you make changes to your tune?

I think it has the ability to select sub maps, which is relative to the main maps.

​it displays a lot of outputs which are correct as its straight from the f-con and the screen can have a choice of showing 2-5-7-10 parameters on the screen

http://www.rhdjapan.com/hks-f-con-navigator.html

  • Like 1

Took the dash instrument cluster out of the Dayz and fitted it to the RS4. Seems to have fixed the problem. Time will tell.

Next prob is getting the aux gauge lights working. I am no auto sparkie and I think I toasted a fuse somewhere.

Just getting back to the instrument cluster, it was quite easy to remove and replace. Used a large mirror to see where all the screws were.

Was glad of the DIY's today. Could not remember how to get to the back of the radio. What a mess I put in there 5 or 6 years ago. Anyway all looks good now. All gauge lights will be working tomorrow. Then on to the aircon condenser fan.

Put on some clear side indicators. They were to suit a pathfinder. Not quite as low profile as the originals bit still look way better than faded orange.. painted the rear impuls black last week then the mrs wanted to go for a drive to kuitpo now its way too cold to paint the front two and she was the one who gouged them up to make me want to paint them :s Also put in some new rear speakers today as the old ones had passed on. 6.5" fit nicely with a small bit of trimming to the plastic bit around the magnet. Just need a radio with frequencies that stops preaching the son of rajab to me haha

post-132120-0-33006600-1398918646_thumb.jpg

post-132120-0-81606000-1398918707_thumb.jpg

Threw my new LED reversing lights in today; BIG difference.

j3ly.jpg

nw6s.jpg

qd06x.jpg

These are the ones I bought.

http://cgi.ebay.com.au/ws/eBayISAPI.dll?ViewItem&rd=1&item=360781669151&ssPageName=STRK:MEAFB:IT

Also gave the headlights a good clean & seal with some Juice sealer. Wish I could still get this stuff.

  • Like 1

Threw my new LED reversing lights in today; BIG difference.

j3ly.jpg

nw6s.jpg

qd06x.jpg

These are the ones I bought.

http://cgi.ebay.com.au/ws/eBayISAPI.dll?ViewItem&rd=1&item=360781669151&ssPageName=STRK:MEAFB:IT

huge difference dale, easy to change?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
    • I checked spark on all cylinders and they all visually have spark with the plug pulled and grounded, but plug 1 is the only one that fouled. This was a running swap that blew up and was rebuilt by a machine shop, put a new wiring specialties harness and did all gaskets, studs, and bolts while it was out.  compression is 135-150 across all cylinders. Aside from that from my understanding with the z32 ecu and maf the car should start regardless. The wiring for TPS and the dual 02 sensor/ dual knock sensor stuff shouldn’t actually stop the car from starting or even running well, (just slightly rich)  they just give fault codes. Car supposedly is supposed to start as long as you have z32 afm and ecu with the nistune base map and that’s info coming from a well known and trusted tuner who does a lot with SR/RB (Rsenthalpy). After more trouble shooting today where I’m at right now is that the cas is sending signal to the injectors they click while spinning the rotor, Fuel pressure is now set at 43psi, all cylinders have good compression and all of the plugs looked great (just wet with fuel) except for cylinder 1 which was very black (cylinder 1 has 150psi compression). all of the coils generate spark if pulled out and grounded out on the head. On the fuel pump car just pops into the exhaust. On starting fluid car will fire off. Hard to tell if all cylinders are firing off but definitley a couple. sounds like all of them but it’s only for 3-5 seconds hard to tell. 
    • Final update!!! Got the front bar fitted and sprayed and all sorted now. My cutouts worked great and the indicators aren’t just falling off. 😂  
×
×
  • Create New...