Jump to content
SAU Community

Recommended Posts

2 hours ago, NicPM35 said:

Here's a quick vid of my previously mentioned exhaust. Couldn't make too much noise because I cbf driving miles away from suburbia 

 

Holy that sounds mint!

  • Like 1

Sound deadening in spare wheel well, makes big difference to resonance on the highway, more of the stuff coming to put in the door skins and rear quarters very soon, then the big banana will be cosy quiet 

DSC_0331.JPG

On 03/12/2017 at 10:40 PM, Long and low said:

Where did you get your sound deadening? Cost? I'll hopefully get a vid up of my exhaust this week 

 

Got it on Wish, took a few weeks to get here but bucketload cheaper....

One sheet big enough to replace the bonnet card and wheel well was $36 delivered, its 10mm thick and compresses to 6mm.

I'll try finding the link to seller and Chuck it up on here for interested parties. 

Edited by oxford1327
  • 3 weeks later...

Just picked up these Rohana RC10 wheels. 20x9 and 20x10 with about 43 offset I think.

Ended up needing 5mm spacers on the front because the offset wasn't quite right, so chasing up some longer studs now I think. Not much thread left with the spacer and the wheel.

Both ends sit out of the guards about 3mm, so should look perfect when I get some lower spings. (anyone got spare lowered springs??)

25590264_10155432159344209_284928527_o.jpg

38 minutes ago, NicPM35 said:

Just picked up these Rohana RC10 wheels. 20x9 and 20x10 with about 43 offset I think.

Ended up needing 5mm spacers on the front because the offset wasn't quite right, so chasing up some longer studs now I think. Not much thread left with the spacer and the wheel.

Both ends sit out of the guards about 3mm, so should look perfect when I get some lower spings. (anyone got spare lowered springs??)

25590264_10155432159344209_284928527_o.jpg

I could sort a deal out with Springs if your in nz? I'm going to put in adjustables in the new year

19x9.5 +22  -cobra lows

DSC_0229.JPG

  • Like 1
1 hour ago, Long and low said:

Good improvement.  I couldn't bring myself to sell my Autech rims. They are just sitting in the garage "in case" 

Spot the Easter egg....

DSC_0267.JPG

Chopped? :P

  • Like 1
9 hours ago, m35stagea said:

Got the shits with stock afm and instability in the nm25 so trialing the z33 r35 unit. 

So do you have to (can you) retune the ECU to suit?

Are you saying the Z33 is the same AFM as the R35?

And will the same unit work on the VQ35DE?

  • 2 weeks later...

Installed the RS-R lowered springs from eBay, plus some new 20x8 Vertini rims which fit properly without dodgy spacers. I won't admit how much time it took me to swap the front springs, but in my defence I had about 1ft on either side of my garage to work with. 

Pretty happy with the outcome! 

20180109_190942.jpg

20180109_191228.jpg

20180109_142805.jpg

20180109_190924.jpg

  • Like 7

So last weekend I did the lower arm bushes , radius rod bushes, sway bar bushes,  lower ball joints and the AFM . My press groaned on some of the bushes. Those things are in there very very tight. The ball joints are a prick! 

Ride improved but it also highlighted just how bad my shocks/springs are. Midday today picked up a set of nearly new Tein GT Wagons and a R33 boot brace to make up a front under body brace. 

Fitted the fronts gonna do the rears tomorrow morning, got late for the rattle gun to be going. Took it for a quick spin around the block , holly crap the difference is incredible. 

 

 

My IT monkey hands are hurting and im cut up but it passes the shoe test. 

 

 

WhatsApp Image 2018-01-13 at 8.20.55 PM.jpeg

  • Like 2

Rear springs and shocks done, front underbody brace bolted up. Its now a totally different car. Why did I not do this sooner :huh:??. Drivers rear shock was completely buggered. Could squeeze it down between  my hands and it took upwards of 3 min for it to extend. 

I set my heights on the bench. Will let it settle for a week and then set again. Just need to buy some C spanners , anyone know where I can buy some in Perth?

Of course all this effort has brought my attention to another clunk. Passenger side tie rod has play. So now need to find a set before I go get new shoes and an alignment.

Suspension sorted now set my sights for go mods:) 

  

  • Like 3

I'm long overdue posting an update.. don't even remember what the last thing I posted was lol 

Anyway, some stuffs has happened, most important one is that my car no longer pings... Took it to E&H Motors out in Pukekohe and they found that the timing was off, which is what I had suspected. A fair chunk of money later i'm happy that the car is now 100% better. 

On a cooler note, I bought a LSD diff which I was gonna chuck into a 4WD stag casing but I derped and forgot about the ABS stub axles.. so now I need to try and find some 3x2 LSD ABS stub axles that I can use... otherwise I might try find some 5x1LSD ABS stub axles and put them in it, but that involves buying the axles as well... 

IMG_0518.thumb.JPG.47145efa2bcb69db02e993f1c1860fab.JPGIMG_0517.thumb.JPG.8ad87bed83f34ddb4bbf91a4b2b8cf00.JPG

 

Also got given a spare casing, but I can't use that anyway. 

IMG_0520.thumb.JPG.1cf6dd5dfe400eafaea942f85e794f05.JPG

 

You can see the ABS ring on the stub axle that I need, apparently the open diff one that I have is too short to be used in the LSD unfortuantly. 

IMG_0540.thumb.JPG.6232f4c9f909abc8761a67c0fa6512c0.JPG

 

Also changed out my coolant and changed spark plugs/coil packs to brand new ones.

Other than that nothing cool has happened haha

 

  • Like 1

Just pressed in a new bearing for the AC idler pulley. Statewide sold me a 6301zz for 5 bucks cause they had em on shelf but not in the POS. :3_grin:. No more howling AC huzzah! 

On 1/9/2018 at 9:23 PM, NicPM35 said:

Installed the RS-R lowered springs from eBay, plus some new 20x8 Vertini rims which fit properly without dodgy spacers. I won't admit how much time it took me to swap the front springs, but in my defence I had about 1ft on either side of my garage to work with. 

Pretty happy with the outcome! 

20180109_190942.jpg

20180109_191228.jpg

20180109_142805.jpg

20180109_190924.jpg

Looking good! So what offsets work on the 8 in rims? Different front and rear?

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The wiring diagram for the R33 RB25 is freely available, and is essentially the same same as most other RBs (just with differences as to which pin # does which job). To get the ECU to power up, you just need to provide power to the ECCS relay, and have the other power feeds that come in from the top left of the wiring diagram (wrt the ECU) that give perma power to the fuel pump relay, the ECU itself, etc etc, all connected. When you put power on all these it will just come to life. It's pretty clear from the diagram what needs to happen. Just follow the lines from the 12V + supply stuff in the top left over towards the ECU. I've even posted snips of such diagrams (not for vanilla 25, I think for Neo and 26) to various threads here in the last few months, talking about what it takes to get the fuel pump and FPCM up and going. Search these up and they will help get you started on doing the same with the vanilla 25 diagram. Hell, for all I know, I've done the same with that one in years past and have forgotten.
    • Yep...so unless someone posts up the answer you will need to probe from the ECU connector to the dash plug with a multi meter in continuity mode to trace the wires.  Note the ECU has multiple - and + (and across different key settings - Battery, IGN and Start) and most likely the power is fed from the connector(s) that is normally near the left hand headlight.
    • Thanks Duncan, I am actually just trying to get the Rb turning and running with the RB25DET S2 original loom itself  I am just trying to get it going outside the body and not thinking about the S15 or trying to match anything to the S15 loom at all I am only trying to see if anyone has done this and what pin they found to be the ignition trigger and ECU+/- on the dash connector, that's about it. Thanks  
    • Hi Guys, Does anyone know any aftermarket part numbers for a starter motor to suit the VQ25DET? I can find lots of alternative part number for the VQ35DE, which I assume would fit, but there is a lot of conflicting information out there. Thanks..
    • I don't understand how this hasn't boiled down to - Upgrade the turbo when you have everything required. ECU, injectors, fuel pump, turbo, etc. Do it all at once.  If you don't have everything required, just enjoy the car as it is and keep saving up your pennies. 
×
×
  • Create New...