Jump to content
SAU Community

Recommended Posts

Lol such hate...

Exempt...

you need to spin the tyres faster for darker lines. Or stay in one spot for longer to leave more rubber on the ground. Try 3rd or 4th gear for more rubber on the ground. In stock form an r32 will hate this... Id reccomend a better clutch and then a bigger turbo and supporting mods.

Softer compound tyres with lower treadwear ratings might also help

have fun and remeber, theres a time and a place. Up the mountain at 3 am is fine but dont go busting huge skids in the shopping mall car park on a thursday arvo...

  • Replies 72
  • Created
  • Last Reply

Top Posters In This Topic

Mate are you just d%^& or what can't you take a hint.

bought mine so i had a decent car to be able to avoid silly little boys who think they can drive.

if ya can't do , save us all the greef.

buy yourself the wheelchair now , leave the rest of us , the tax payer and the light poles alone.

i can bet 99% of skyline owners have done a skid in there car lol, does matter what tyre you have, its heat what causes the rubber to melt and leave the marks, a skid with no wheel speed will just take rubber off and leave no mark, go to a skid pan and practice or at home in your shed, keep it off the roads, im over getting pulled up because the copper hunts skyline because there hoon cars.

pull off the line to the wastegate actuator and enjoy the next week.

OP, this is the key to making darker lines on the road!

More boost = more power = more black marks on the road.

Simple as that!

Remove the wastegate line and go nuts! Nissan only installed a wastegate as an emissions control device, like the carbon canister, it's not really necessary...

pouring a bottle of metho in the tank helps as well

Who the f**k doesn't lay the occasional snakey???

You must all have baby seats in your skylines ay.

yes i do have a baby seat, how did you know..

Oh and it will lay a way better snakey than yours too but I prefer not to ruin my car for your amusement....

EDIT..actually my work ute would lay a way better snakey than your car, man you really are a loser..

LOL so much hate, poor guy lol

Ask a stupid question, Get a stupid answer lol simple as that

I dont do static burnouts, I snapped a halfshaft last time I did one (which was the first one I'd done in ages anyway) so no I rarely do them

I find it more enjoyable when the car grips and takes off quick and drives nicely rather then sitting with my bogan friends comparing black marks.....

Eat heaps of vindaloo currys and a box of laxatives and wait 30minutes then go do skid marks galore :thumbsup:

Lol I don't think they are the sort if skid marks you can be proud of and show your friends... Then again it depends on who your friends are

I don't have a problem with burnouts, each to their own in that department, but the cops/law do have a problem with it...and every twit they catch doing burnouts on the street in a Skyline is another step back for Jap car enthusiasts who don't want the negative cop attention / the canary.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...