Jump to content
SAU Community

Recommended Posts

I have 4 cans.

I'd budget 1 x 20L Jerrycan of fuel each way to Winton or PI.

Which leaves me with only 80L of usable fuel for on the track. May need to invest in a few more Jerrys...

Still a bit concerned about fuel sitting for so long once I switch to 85... when I was filling with P100, I'd just use the remaining fuel to fill the daily over the next 2 weeks.

Yeah Winton is quite a bit more distance for me

PI is only about 120kms. So 2/3rds a tank for travels than the rest of racing

I wont be doing winton till I get some sort of flex fuel happening from Trent

I've driven to PI from the west on E85 with only 3 jerry's n raced all day. Fill up in Cranbourne, race all day and then stop at Cranbourne again on the way home.

That's good to know :thumbsup:

I find I use much more at winton as you get so much more track time.

plus sandown as you have the throttler open so long each lap.

PI you only get 3-4 sessions normally so not as bad,

calder you get bored after 2 sessions and go home ;)

I have 4 cans.

I'd budget 1 x 20L Jerrycan of fuel each way to Winton or PI.

Which leaves me with only 80L of usable fuel for on the track. May need to invest in a few more Jerrys...

Still a bit concerned about fuel sitting for so long once I switch to 85... when I was filling with P100, I'd just use the remaining fuel to fill the daily over the next 2 weeks.

chuck evo on e85 too. simple.

I carry my laptop with me and when I run out of E85 with no E servos in range, just switch to a rich 98 tune when there's about 5-10 litres left. Runs on this mix fine, can even give it a boot.

Flex is for poor planning.

I carry my laptop with me and when I run out of E85 with no E servos in range, just switch to a rich 98 tune when there's about 5-10 litres left. Runs on this mix fine, can even give it a boot.

Flex is for poor planning.

this!

that PI will not be in the MS championship as a bunch of us will be unable to attend.

but I know the guys are working on dates as we speak, with some big improvements over last year.

Any ideas on when & where the first one will be?

PI ride days are like $285 this year, quit your bitching

We need to hire MICA Paramedics, Recovery Crew etc...

You guys need to pay for a cleanup truck as well to remove face chunks from the track.

http://mypolice.qld.gov.au/rockhampton/2015/01/08/police-warn-motorists-not-block-speed-cameras-man-charged-rockhampton/

Well which is it? "High Visibility Policing is an effective deterrent for speedsters" or "Camera cars are now able to disguise themselves and hide (for their own safety)"

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...