Jump to content
SAU Community

Recommended Posts

hey guys wondering on everyones opinion on how you launch your GTR for the 400m

to get the best 60ft..

depending if you have a clutch you can ride or not, in my case its either on or off. so launching 5k/ 6k just bogs a little on take off but no wheel spin.

i tried a 7k launch and it wheel spin all of first and got me my best time. is there better ways of doing this?

cheers

Link to comment
https://www.sau.com.au/forums/topic/392983-how-do-you-launch-your-gtr/
Share on other sites

My best 60ft was a 1.59 not sure if thats good or just average. (33gtr)

was by just sidestepping the clutch at just under 8000rpm (in first gear) an planting throttle. the car got full traction at about 5,500rpm. had a set of 275/17 falken 452's i think (just normal street tyres) been back with cheap rubber an less power an couldnt get it to hook up spinning all of first = shit times

Honestly side stepping sounds impressive but is very hard on the drive train. Basically you are jolting any loose slack immediately with a lot of power. I prefer (as mentioned on several folks here interested in keeping their drive train on the car instead of under it) to preload using the handbrake. Bring it to 7-8k revs, hold handbrake and let out the clutch just enough until you feel the car lurch forward. Then you can sidestep on the green but you aren't jolting the drivetrain nearly has hard.

  • Like 1

Also, I found that 22psi launched the best. Sounds low but has lots of initial bite. I've only done one full day of drags so interested in hearing what others run for tyre pressure on standard streets/semis.

Honestly side stepping sounds impressive but is very hard on the drive train. Basically you are jolting any loose slack immediately with a lot of power. I prefer (as mentioned on several folks here interested in keeping their drive train on the car instead of under it) to preload using the handbrake. Bring it to 7-8k revs, hold handbrake and let out the clutch just enough until you feel the car lurch forward. Then you can sidestep on the green but you aren't jolting the drivetrain nearly has hard.

yer that is a good idea, tried it a cpl times, tho the first time i probably got ready a lil early an the guy beside me didnt seem to be able to line his starting lights up so by the time we eventually went i had that nice clutch smell through my car. definately agree it would be easier on the driveline...cept the clutch. tho i never broke anything..not sure if its just good luck or the drivelines are just that tough.

My best 60ft was a 1.59 not sure if thats good or just average. (33gtr)

was by just sidestepping the clutch at just under 8000rpm (in first gear) an planting throttle. the car got full traction at about 5,500rpm. had a set of 275/17 falken 452's i think (just normal street tyres) been back with cheap rubber an less power an couldnt get it to hook up spinning all of first = shit times

Thats a quick 60ft'er! What time did you end up running ??

My best 60ft was a 1.59 not sure if thats good or just average. (33gtr)

was by just sidestepping the clutch at just under 8000rpm (in first gear) an planting throttle. the car got full traction at about 5,500rpm. had a set of 275/17 falken 452's i think (just normal street tyres) been back with cheap rubber an less power an couldnt get it to hook up spinning all of first = shit times

How much power to spin up all four? I have an awd Stagea with GTR gearbox and diffs and want to try for a 1/4 mile time (never been) - I will have somewhere between 300 - 350 awkw and I fear that just dropping the clutch at max revs the 255s won't spin but something will go bang!

I recall reading about the Group A R32 GTRs being launched at redline and one of the drivers being uncomfortable about doing it that way.

When I watched Best Motoring in those endurance races, they launched the R32 and R33 GTRs in 2nd gear.

  • Like 1

As for how strong the drivetrain etc is. I've had 2 R33 GTR's and many different gearboxes, launched them hundreds of times and never broke anything launching. And never really bothered with any pre-loading or anything. One with only 400rwhp and one with lots more, always spins all 4 when you dump it. For the 1/4 it's definitely going have a better chance of hooking up with a little clutch slip.

To the OP, getting 1.5 60foot on streets is awesome. Especially with just stepping off the clutch cheers.gif

11.7sec ran 3 11.7's for the night tho 60ft got a lil slower later on as it cooled down but had a higher trap speed the 1.59 60ft run was at 185km trap speed an 1.71 was at 189km/h an had 1 run somwhere in between them all 11.7's also did 3 other not so good runs for the night. was my first time at the drags so was happy. 385hp at the wheels

can someone please explain side stepping?

i got a 1.89 60ft by dropping the clutch at 7k with wheel spin all of first on the limiter lol. ran a 12.1

got 315 rwkw with 255/35/18 profile tyre. kept pressure at 36 because it was still bogging down at 6500 rpm .

with my setup how would use do it?

can someone please explain side stepping?

i got a 1.89 60ft by dropping the clutch at 7k with wheel spin all of first on the limiter lol. ran a 12.1

got 315 rwkw with 255/35/18 profile tyre. kept pressure at 36 because it was still bogging down at 6500 rpm .

with my setup how would use do it?

what u are doing is called side-stepping, revving up close to limiter and dropping your foot off the clutch completely when launching

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Welcome to Skyline ownership. Yes, it is entirely possible parts websites get things wrong. There's a whole world of inaccuracies out there when it comes to R34 stuff (and probably 33 and 32). Lots of things that are 'just bolt on, entirely interchangable' aren't. Even between S1 and S2 R34's. Yes they have a GTT item supposedly being 296mm. This is incorrect. I would call whoever you got them from and return them and let them know the GTT actually uses 310mm rotors. Depending on where you got them from your experience and success will obviously vary.
    • Hi...a bit a "development" on the brakes. I spoke to the guys where i get brakes from...and they are saying that 296mm EBC are for R34 GT-T. I then went to their site: https://www.ebcbrakes.com/vehicle/uk-row/NISSAN/Skyline (R34)/ and search for my car(R34 GT 1998 - it has GTT brakes) and it show me this USR1229 number and they are rly 296mm rotors... So now iam rly confused... The rotors i have now on the car are 310mm asi shown... So where is the problem? Does the whole EBC got it wrong or my calipers are just...idk know what?  
    • Oh What the hell, I used to get a "are you sure you want to reply, this thread is XX months old" message. Maybe a software update remove that. My bad.
    • This is a recipe for disaster* Note: Disaster is relative. The thing that often gets lost in threads like this is what is considered acceptable poke and compromise between what one person considers 'good' looks and what someone else does. The quoted specs would sit absurdly outside the guards with the spacers mentioned and need  REALLY thin tyres and a LOT of camber AND rolling the guards to fit. Some people love this. Some people consider this a ruined car. One thing is for certain though, rolling the guards is pretty much mandatory for any 'good' fitment (of either variety). It is often the difference between any fitment remotely close to the guards. "Not to mention the rears were like a mm from hitting the coilovers." I have a question though - This spec is VERY close to what I was planning to buy relative to the inboard suspension - I have an offset measuring tool on the way to confirm it. When you say "like a mm" do you mean literally 1mm? Or 2mm? Cause that's enough clearance for me in the rear :p I actually found the more limiting factor ISNT the coilover but the actual suspension arms. Did you take a look at how close those were?
    • @GTSBoy yeah sorry i know thery are known for colors bud those DBA are too in colors 🙂 Green will be good enough for me  
×
×
  • Create New...