Jump to content
SAU Community

Recommended Posts

43 minutes ago, Mick_o said:

What are the temperature ratings on the Festo pneumatic hose and fittings?  It looks nice and neat and definitely easy to install. But I'm a bit sceptical it would live long on the hotside there? ?

80 degrees c for the nylon fittings, reasonablysure the tube if nylon would be good to over 100 c.

If I was to use push for fittings I would use metal ones, although aerofloe also sell nylon pushfit fittings and some pretty serious cars run them for waste gate plumbing.

 

 

15 minutes ago, Ben C34 said:

80 degrees c for the nylon fittings, reasonablysure the tube if nylon would be good to over 100 c.

If I was to use push for fittings I would use metal ones, although aerofloe also sell nylon pushfit fittings and some pretty serious cars run them for waste gate plumbing.

 

 

Cheers for the info! I think I will still remain sceptical of their long term reliability lol

  • Like 1
16 minutes ago, Mick_o said:

Cheers for the info! I think I will still remain sceptical of their long term reliability lol

Same! Sure as hell wouldn't be doing that without protections for over boost setup!

 

I ended up going nuts and running 200 series -3 fittings there as the tube i had was breaking down and giving me boost controller issues, or so I thought.

Turns out the wires on the MAC solenoid plug had got hot and broken...

Oh well i know it really won't leak now though.

2 hours ago, Mick_o said:

What are the temperature ratings on the Festo pneumatic hose and fittings?  It looks nice and neat and definitely easy to install. But I'm a bit sceptical it would live long on the hotside there? ?

Not sure what the temp rating is for the lines and fittings. I haven't finished the build yet and will be putting heat sheathing on each of the lines to keep them from melting. My manifold, gates, and turbo also have lava wrap and blankets on them to help reduce heat.

  • 2 weeks later...

Hello all, I have a 1972 Datsun 240z with rb26 on an efr 8474 ewg with sinco custom dual 38mm tial and 3.5” exhaust. Unopened motor r33gtr rb26, has r35 coils, prp trigger kit, 180amp alternator, elite 2500, id1050x. Hks step 1 264 cams, adjustable cam gears( not adjusted). Had my first dyno tune with the car/engine a few days ago to 415rwhp and 352ftlbs of torque on 15lbs, USA dyno, 91oct. The concern I have is the time it takes to hit full boost on the efr8474, I’m not hitting full boost until 5,500rpm (15lbs no ebc, just wastegate springs). I was expecting this turbo to hit full boost around 7-800 rpm sooner at that boost level. I have a small vacuum leak and my wideband wasn’t working are the only issues I had... is there something possibly wrong or is this rpm boost expected with my setup?

 

Edited by brian_s30z

adjust the cams? That's really late for 15psi but reasonable with poorly optimised cam timing.

Is your boost control soft? Holding the solenoid on while your spooling can help too.

Boost leaks don't help either

Edited by burn4005
1 hour ago, burn4005 said:

adjust the cams? That's really late for 15psi but reasonable with poorly optimised cam timing.

Is your boost control soft? Holding the solenoid on while your spooling can help too.

Boost leaks don't help either

He has no boost control. 

I do have a boost solenoid but per the psi I wanted 1bar, the springs are all that’s workingboost control. Hopefully cam adjustment will do the trick, once I fix leak and o2 sensor I’ll try to dyno again. But with cam adjustment I still think I’m a bit off. I’ve read folks with 9174 with unopened rb26 hit full boost low to mid 4K rpm

rb26 swapped 240z sounds like fun!  but 1bar boost at 5500rpm is definitely not correct for 8474 on rb26.  Boost leaks are a big issue, and exhaust leak is equally likely, given how laggy the boost is coming on.  2 smoke tests (boost leak and exhaust leak) are recommended

  • Like 1

GFB DV+ T9360 is a re-circulation valve designed for OEM used BW turbos, while not officially advertised to fit an EFR by GFB, I have tested fits on an EFR.

All bolt holes align.  Plunger seal is pretty much the same diameter as the face inside the compressor housing so it seals.  Piston is workable length to be able to vent when fully compressed into the BPV body.  One slight issue is outer seal on compressor housing doesn't sit in factory grove but still sits on a flat surface on the compressor housing

Edited by RB335
  • 2 weeks later...
12 minutes ago, brian_s30z said:

Checked my ignition timing and it was on 10btdc. The haltech has it on 10degrees too. Tuner is going to verify and fix, hopefully that is the reason 8474 is coming on late 

There's nothing  to fix. They need match between ecu and light, that's all. They do match.

 

  • Like 1
27 minutes ago, brian_s30z said:

I thought is suppose to be set at 20btdc..?

With the haltech (and other ecus) all that has to happen is they match. Can be any number you want with an ecu that you can lock the timing to that chosen number. Change it to 20 in the haltech and chech with gun, it will be on 20.

 

  • Like 1
57 minutes ago, brian_s30z said:

I thought is suppose to be set at 20btdc..?

Yes. And no. What Ben is trying to say is that the sync timing is not the idle timing.

Manuals (RBs) should idle at 15°. Many of the autos idle at 20° because it makes them have a little more torque at idle which is needed to keep the engine working against the load of the torque converter.

The sync timing just means that the ECU knows what the actual engine angle is. The actual timing that is run at any moment is then simply what one table or another in the ECU demands. 4000rpm and 20 psi of boost? Likely to be about 20°. That's 20° exactly, because the ECU knows where zero is (because the ECU was told where 10° was).

  • Like 1
  • 2 weeks later...

Hi all. I’m currently installing my EFR7670 setup on my R33 GTR and have some questions on finishing it up

 

  1. Should i route the water feed line from the feed line coming from the back of the engine and T to the block, similar to the stock turbos setup? Can I just do the water feed from the block near cylinder 5 without having to bring in the rear line from the other side of the motor?
  2. Should I follow BW’s directions and plug the water feed on the bottom side and water return from the top side of the turbo? 
  3. What’s the max boost I should consider? I know it runs on the smaller side but want to avoid over spinning the turbo (it’s a EWG 1.05 AR)
Edited by cachorro

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • @666DAN sorry to bring you and old thread.     I've got my de+t done and it's all running great other than 1 small issue.    Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd when selected . But nothing when in  drive or what gear your in when you pop it into tiptronic. I'm sure there is maybe 1 wire in the ecu plug I need to move to rectify this. Do ya have any ideas?     Cheers man
    • Well I recently changed my rear axles and was thinking if I bumped anything, I have been driving the car for a while now though... But it has been raining today so everything is wet under the wheel arches. Brakes feel fine and can't hear any of the metal screamers, I had a squeak coming from one of the handbrake drums but that seems to have gone away a while ago. I was going down a hill when it lit up and I did feel the abs bite for a second and question why it did it?
    • Correct. Um. I dunno. I haven't cared enough about the way that the NA cars work to know for sure. But..... The 33/34 turbo manual cars have an electronic speed sensor in the gearbox that outputs a +/- (ie, sawtooth AC) voltage signal. That is connected to the speedo. The speedo then outputs a 0-5v square wave (ie, PWM) signal that the ECU (and any other CU on the bus) sees. The speed sensor is NOT directly connected to the ECU. So here's the problem. Your new ECU expects to see the PWM signal, but must somehow be getting a direct signal from the diff speed sensor. Which would suggest that the wiring of the NA car is not the same as the turbo cars. I think you will need to spend some time with (hopefully the wiring diagram for the car) and a multimeter to see what is connected to what. Then, presuming I am correct**, you would then want to separate the ECU speed signal input from the rest of the car's wiring, and probably either buy a speed signal converter, or build one using an arduino (or similar). That would take in the speed sensor signal and output a scaled (and suitably rearranged) signal for the ECU. ** We shouldn't presume that I am correct here, because there might be something else crazy going on. I don't think you could convert the speedo to be fed from the gearbox sensor, because the pulse rate from that sensor is probably different to the diff sensor and then the speedo would read wrongly. And this also wouldn't fix the ECU's problem either, because the ECU doesn't want to see the gearbox signal direct either (assuming that they are all on the same wiring, for some odd NA related reason, see above caveat!) Does this help? Probably not. Can you make it work? Almost certainly. With the above work. You should buy a handheld oscilloscope from Aliexpress so that you can view these signals directly. Connect up the probes and drive the car. Show photos of the screen when drving at known speeds and connected to different places, and we'll see what we can learn about it.
    • Assuming your brake pads are not worn right down, I'd add a little brake fluid. Is there any sign of a brake fluid leak?
    • Hello all,  I need of some help. On my drive home my handbrake light lit up and started flashing. When I got home I checked my handbrake sensor under the centre console and nothing seemed out of the ordinary. I have scanned my car via the consult port, no codes shown. Checked my brake fluid as well which is half full. Tried unplugging the brake master but it didn't change anything. Thoughts on what it could be? The master float doesn't seem to be stuck. My car is an 1998 ER34 sedan GT. No hicas but has ABS Photos below 👇🏾 
×
×
  • Create New...