Jump to content
SAU Community

Recommended Posts

4 hours ago, brian_s30z said:

Nah, I doubt it. I already see the meme of the disappointed kid looking at paper (car meme is dyno sheet). “Spends $4k to improve response by 1,000rpm+, only gets 400rpm difference.” 

 

You're not sprinkling fairy dust on it, they're mechanical modifications that are proven to work. The variable turbo side of it isn't proven as a specific product yet but the concept is to make it a smaller turbo (which is well proven to add response) until you need it to be a bigger turbo once its spooled up.

Even if it was "only" 400 rpm lower in the rev range that will make a massive difference to your response. Arse dyno can definitely feel the difference! 

i have a set of the borgwarner VTV housings if anyone is wanting to do a similar setup.  They did not work well for me in twinscroll configuration, despite my initial expectation.  I hope turbosource has got it figured out, but it definitely does work in open volute/singlescroll 

Here's my 7670 with a little more boost added in. We are at 129K now. Pretty much going to leave it where it is now. 

Highest power I have seen here in Oz is 418kw ALL IN (on an evo too) that power was made on 235s. My car runs 265s and I have actually back to back tested my car from 235s to a 265 on the exact same tyre (Hankook RS4's) and I lost almost 15kw between the 2 sizes lol.  

20201030_174351.jpg

  • Like 1
1 hour ago, R32 TT said:

Surely the bigger number is the 9180...  (but yes, that could be wrong).      I bet the 8474 must be different to drive though.

8474 flows more than the 9180 lol 🤷‍♂️

Red line is 9180, Blue line 8474.   From limited street driving I can't tell a real difference at all in most conditions, no turbo is the clear winner but im inclined to feel the 9180 better suits my engine so far.  I'll do some more testing with high lift cams and a 9280
 

Edited by RB335
On 30/10/2020 at 12:40 AM, RB335 said:

My EFR9180 and EFR8474 on 2.8 with Vcam Step II / ex HKS 272 8.7

Absolutely visceral to drive 

 

 

20201014_182343.jpg

At what turbine speeds? Both of those look far from “all in”. Considering an 8374 will piss in 600 whp, why are a 8474 and 9180 which flow far more only touching those numbers? 

Have you you got a decent exhaust on it yet or does it still have that 2.1 inch thing you said was on it a while ago? If that has not been addressed you are wasting your time.

  • Like 1

So Benny carried out a turbine housing touch test. After a 20 minute drive he touched the compressor housing, that was cool enough and then dropped a finger on the turbine housing. Even the 1.05 T4 was hot. This was the result. 
 

🤣

4BD860AC-3BDF-4F85-B998-C9D78EDEF6D7.jpeg

D615E90F-D8C2-4093-85D5-2E6C6C879C2D.jpeg

  • 4 weeks later...

Semi off topic, but Geoff. Is there any way if getting some of the EFR 3D models that I have been seeing used (SEMA shows, Papadakis exhaust manifold video etc) I have searched, but found nothing really. 

 

I have no commercial interest with it, I'd just love to print one :)

14 minutes ago, taijohnsen said:

Semi off topic, but Geoff. Is there any way if getting some of the EFR 3D models that I have been seeing used (SEMA shows, Papadakis exhaust manifold video etc) I have searched, but found nothing really. 

 

I have no commercial interest with it, I'd just love to print one :)

you've been watching the latest papadakis manifold vid havent you!

  • 1 month later...

@Timmaz300 looking really good so far, keep up the good work!

 

@all: A friend of mine is collecting parts at the moment to go for about 600 (engine) hp and has snacked up a 8374 IWG.

What are the options for the wastegate actuator on the IWG EFRs?

Electronic actuator (with supra parts) as suggested in this thread in late August will probably be too expensive for him (500+ $/€ ?), because he just spent loads of money on parts. Are there even any complete kits available now or is it still "do it yourself"-style?

The OEM actuator on the EFRs are the known weakpoint on the IWG EFRs, at least thats what this thread and similar threads on other forums suggest. So I wouldn't recommend this to him. If he does go this route, he will definetely need the high boost canister, because otherwise he wouldn't even be able to reach around 15 psi?!

This leaves us with conventional aftermarket actuators, for example from turbosmart.

Twin Port is probably the way to go here, because the price difference is not that big. Right?

What about the position sensor? Is this necessary on a road car or similar to the BW turbo speed sensor (not a must, but very nice to have) or not necessary at all?

Is there a noable difference in performance between the GenV and the IWG-75 twin port turbosmart actuator?

Thanks guys 🙂

And regards from Germany!

Edited by MotHot

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi, i’m making a rb25det coil loom for Vag short coil. Can anybody tell me which Ecu signal wire belong to coil number 1 and 2,3,4,5,6? The connecting switch in above pic is 8 wire i think white is for +12v and black for earth.
    • Was there ever a model of the Stagea m35 that didnt have a badge on the grill? I thought I saw that somewhere, some aero edition or something? I cant find it again? davemoto
    • Its a 2002 vr-x four VQ25DET, silver. Coil overs, lowered, polished alloys and sport exhaust. Bit of a project, was sitting in a shed for a while but runs and drives great.
    • I wasn’t able to replicate the sound anymore. It was a one time sound so maybe it was just coincidence but it was like small pebbles being dropped in a coke can.   should I try cleaning the MAF? It could be it’s functioning but dirty? I don’t know.
    • Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
×
×
  • Create New...