Jump to content
SAU Community

Recommended Posts

That one is a bitch to change

Good luck

Thanks prob get some mates over so I don't have to do it all alone and to talk shit

Sorry to hear mate, Buy some gaskets and change anything suspect while your on the job :)

This will be the go if I'm changing that may as well fix the lot

G2.5 is a smaller turbo then a G3, they generally maxing out towards 260rwkws mark. So its about at its limit.

He's right, the graph shown is for a G3, but the intake leak might still be present and causing the 5ish psi boost drop. Fixing it might get him another 10-15kw from threshold to redline, definitely worth investigating.

http://www.hypergearturbos.com/atr43.html

The link says G3 but that is the graph from the G2.5 on the page. Either way I will suss out any leaks and give it another run soon.

That G2.5, I thought was a high flow. Preload the actuator about 10mms, if it starts to pin then its usually a restriction some where. This one don't have much of boost drop.

also stao,

your new website isn't meta tag searchable/ google submitted as i cant seem to find the new one on google which is meant to have more details on your range then the old website

That G2.5, I thought was a high flow. Preload the actuator about 10mms, if it starts to pin then its usually a restriction some where. This one don't have much of boost drop.

Hiflow of a stock 25 turbo? It has a 3 inch inlet so i don't think so

lol... does it fry tyres when you smash the pedal?

Yes it does, because the car is so big and front wheel drive, it wheel spins on the spot with stock tires. lol

Hiflow of a stock 25 turbo? It has a 3 inch inlet so i don't think so

Preload the actuator to about 10mms. If you a have a boost gauge, check the pressure drop before and after the cooler, also try a run with no exhaust on.

Yes it does, because the car is so big and front wheel drive, it wheel spins on the spot with stock tires. lol

Time for some M/T tyres? :P lol

This is for a good comparison of the new ATR28SS1 V ATR28G1 based on the Kia's G4GC engine:

SS1 at 8psi, G1 at 12psi:

ower:

Thin red: SS1 @ 8psi,

Green: G1 @ 12psi

Thick Red: NA none turbo @ 0psi

ss1vsg1power8psi.jpg

Boost:

Green is G1,

Yellow is SS1

g1vss1boost8psi.jpg

SS1 at 14psi, G1 at 12psi:

ellow: SS1 @ 14psi

Green: G1 @ 12psi

Red: NA @ 0psi

g1vss1power14psi.jpg

Boost:

Yellow: SS1

Green: G1

g1vss1boost14psi.jpg

This is an excellent turbo for around the 200rwkws on a SR20det.

I don't think that would be a problem. I can upgrade it to the latest profile, which is targeted at boost dropping issue with internal gate. PM if interested to go ahead.

Those are a set of CT20 Toyota Supra turbochargers that I've recently done. Those are rated to about 400HP each. Running ATR28G3 CHRAs. photos shown compressor and turbine wheel comparison, profiled compressor and turbine housings, and completed turbocharger assembly.

chra.JPG

turbine.JPG

housing.JPG

turbos.JPG

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Ok i will get those 310mm. I found one but on a different site. This is the description on those...is it ok? Technical parameters: - Axle: front. - Disc type: ventilated. - Number of holes: 5. - Disc diameter: 310mm. - Total height with center: 54mm. - Thickness (new/min.): 30/28mm. - Designed for brake calipers manufacturer: Sumitomo.
    • You Gregged a whole racetrack!?
    • Look for broken wire or bad connector at the motor. Might not be it, but is worth starting there, as it is easy.
    • Hi everyone, I’m having an issue with my R32 GT-R. Sometimes, when the car goes over a bump or experiences some vibration, the 4WD warning light comes on the dashboard. When I check the code from the control unit in the trunk, it shows Code 19 – ETS Motor. However, everything seems to be working fine — if I turn off the engine and restart the car, the light goes away and everything functions normally. Has anyone experienced this before? Where should I start troubleshooting this issue? Thanks in advance!
    • I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
×
×
  • Create New...