Jump to content
SAU Community

Recommended Posts

Yeah but what car would feel awesome to them?

Might as well drive a shitbox.

See, now as I wrote my post, that thought crossed my mind...but the way I see it, you're never gonna match the F1 car, but given you have the means, why not get as close to it on the road as possible?

  • Like 1

I read many years ago an interview with Ivan Capelli, then Fezza F1 driver.

His Ferrari sponsored road car was an F40, and when quized, he said while yes, it was "fast", it was in no way even remotely comparable to F1, and therefore not at all exciting.

We all know that, but I guess many less educated than us would think that a road Ferrari is fast in outright terms.

And whats with the Mark bashing? The bastard can drive.

I read many years ago an interview with Ivan Capelli, then Fezza F1 driver.

His Ferrari sponsored road car was an F40, and when quized, he said while yes, it was "fast", it was in no way even remotely comparable to F1, and therefore not at all exciting.

We all know that, but I guess many less educated than us would think that a road Ferrari is fast in outright terms.

And whats with the Mark bashing? The bastard can drive.

A long time ago a bloke by the name of Phillippe Alliot was the test driver for McLaren when they were running Pug engines. Anyway there was a trumped up road car versus 2 litre touring car versus F1 article in Car mag. Asked what he thought of the road car (a Peugeot three oh something) he answered: any road car is a total disaster on a race track. Now that is quality PR.

Ivan Capelli was the man when he drove for March. But Ferrari screwed him over massively after making him drive what was up there with the worst Ferrari F1 cars of all time.

yeah it's entirely understandable to have zero to no interest in road cars when for 30 - 40 weeks a year all you are thinking about is driving your 7 speed, 800+hp, super duper F1 car. as they all pointed out no road car on the planet offers anything like the limits those guys are used to. anyone who can punt an F1 car hard can surely drive most anything pretty close to it's limit. and as the years have gone on the gap between road cars and F1 cars has surely widened a fair bit too.

And whats with the Mark bashing? The bastard can drive.

Webbo can drive better than any of us ever will, to be sure. Only problem is He can't consistently driver better than the small gaggle of bloques that'll keep him from that elusive WDC.

Webbo can drive better than any of us ever will, to be sure. Only problem is He can't consistently driver better than the small gaggle of bloques that'll keep him from that elusive WDC.

hmmm... I would agree, but then remembered that you don't have to drive consistently better/faster than the other to win the WDC.

Just ask Jenson Button

And whats with the Mark bashing? The bastard can drive.

No he can't, he's a hack choker who doesn't deserve to be there. None of us would be talking about him if he didn't come from Aus.

Webbo can drive better than any of us ever will, to be sure.

I'd need a back to back test in the GTR to be sure :P

No he can't, he's a hack choker who doesn't deserve to be there. None of us would be talking about him if he didn't come from Aus.

I used to be in the same boat. I use to really like/rate Heidfeld and thought he would hand it to Mark when they were at Williams. But Marlk surprised me with just how fast he is. In my eyes he is as good as if not a tad batter Rosberg, Massa and Button. Not quite as good as Hamo, Alonso and Vettel.

Vettel cant race to save his life, but he is fast. Webber isnt far off his pace, typically less then a tenth in quali, and hey he did outqualify him 6 times and beat him a number of times.

So he does deserve to be there....and I used to like guys like Fisi until he got blown away by Alonso. Heidfeld but then he has not done anything alongside Webber or Kubica....so Webber has never been embarrassed by a team mate :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
×
×
  • Create New...