Jump to content
SAU Community

Recommended Posts

I've never had a steak go cold on me, apart from the 1kg challenge I did...

What if you're no good at cooking steak...?

And if you go to a good steak restaurant /good restaurant in general, your steak will be juicy

Well true it doesn't go cold, but a normal steak doesn't stay anywhere as hot as stone grill. It's like that first awesome bite of steak, but over and over again. Old man travels across town just for it haha

Ain't really cooking it yourself anyway, cause it cooks quick enough that you're pretty much just cutting pieces from the block as they cook; it's hard to screw up unless you're a real slow eater, but can always pull steak off the stone I guess.

Haven't even taken delivery.... just signed contract.. should have it in a week.

it's not exactly a 300rwkw R33... but it is far more convenient for driving kids around which now make up some 99.27% of my driving

lol @ single mum.

is $160 fair price for A/C re-gas? (from scratch, not top-up)

bit tasty, but its summer so 30% increase.

check out cranbourne auto elec. ihe was a top bloke, charged me 180 for a service, few orings, labour for repair and gas on wrx.

Tony have you got the dyno read out from your 380rwkw with a 3" exhaust? Boss has told me in the past that it's almost impossible to see over 330kw with a 3" exhaust.

Yeah it was on Trents dyno, did a drop of the exhaust and no restriction

Its a jjr 3 inch dump and cat, then get slightly bigger to the muffler

Refitting for that new style refrigerant as well?

Y34 should already be R134a, even 33's are already. 32 etc need to be converted from R12 doe.

AC in the new RS is f**king awesome. Have receipts for regass done in 97 and then again in 2011. On the way back home from shitney had to keep turning it off cus it was too cold.

  • Like 1

Tony have you got the dyno read out from your 380rwkw with a 3" exhaust? Boss has told me in the past that it's almost impossible to see over 330kw with a 3" exhaust.

Yeah it was on Trents dyno, did a drop of the exhaust and no restriction

Its a jjr 3 inch dump and cat, then get slightly bigger to the muffler

669.gif

  • Like 1

Tony have you got the dyno read out from your 380rwkw with a 3" exhaust? Boss has told me in the past that it's almost impossible to see over 330kw with a 3" exhaust.

aye is pvc pipe okay? Ill use the proper plumbers cement.
Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • I was 99% sure the standard one is long enough to get there, you might just have to change the throttle orientation. If not, I remember someone having used an r31 cable instead, but that is probably harder to find than r33 by now...
    • HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
×
×
  • Create New...