Jump to content
SAU Community

Recommended Posts

I just got a cheap second-hand Logitech GT. Not as nice as a G27 but can't complain for $60.

If you and Michael compete next week, should be a pretty full grid. Can keep me company at the back of the pack :P

Best thing I did was focus on setup and tweaking FOV to suit my sitting distance from the screen. Really helped me judge braking distances

Leroy is right about setup. Brake setup is uber important when its a fixed setup race too ;)

Playing a little bit with FOV am i right in assuming for a single 70" about 1.5meters away i should basically be using low as fark 45FOV? I think i need to sit closer lol.

From my brief research looks like single monitor = 45-60ish and triple much higher correct?

Edited by UNR33L

Edge motorworks sounds promising

Call and Barry answers

Him: You vont stroker?

Me: Yeah that or an RB30 bottom end

Him: Yah 30 torque monsta...lots of power...do that

I like where this is going

  • Like 5

Edge motorworks sounds promising

Call and Barry answers

Him: You vont stroker?

Me: Yeah that or an RB30 bottom end

Him: Yah 30 torque monsta...lots of power...do that

I like where this is going

lol.

I actually heard that in his accent too.

Edge motorworks sounds promising

Call and Barry answers

Him: You vont stroker?

Me: Yeah that or an RB30 bottom end

Him: Yah 30 torque monsta...lots of power...do that

I like where this is going

Thought you were going racepace rebuild?

That was the preference but

Last communication to RP was to keep me regularly updated on free spaces in the workshop

2 months later still nothing

I'll pass

No hard feelings from me, but it ain't hard to send a weekly email or knock back the work and say try again in 3 months or something...stringing along is wasting everyone's time when my engine could be getting built right now

They obviously get enough work from their loyal motorsport customers and need to service them as a priority which is fine, but I need to get this thing on the road

Hatish you tried Easey’s burgers yet?

do you rate?

tried Laurie Dee's the Burger adventure winner from last year this week, was very unimpressed.

looking for a new one.

I went to bad boys Melbourne. $15 meal was pretty good value. Tasted great

Took 2.5 hours to drive from sunbury to rowville this arvo.

Mostly due to the Burnley tunnel having a lane closed to half of it for no reason at all.

And then this weekend is going to be spent cursing at the astra.

Hatish you tried Easey’s burgers yet?

do you rate?

Yeah, the owner and chef are mates of mine.

I went when it was a popup for a week on the rooftop of an apartment building on bourke st and it was amazing.

If jimmy & josh can keep up that quality then it will be number 1 without fail

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • Thank you, 100% the intent. New coils were due and the 17" sixers look/feel loads better than the stock wheels. The aero options are so spot on.   Thanks for the warm welcome, all!
    • 98 r34 gtt Been rocking my latest setup and car running like never before. Have put a good 200 miles on it since all the latest changes and additions. everything is dialed in and have been driving it a bunch.   However, all a sudden last weekend as soon as I pushed throttle passed 4k and the engine stumbles, (slow or fast acceleration) hesitates and doesn’t go above 4100 or so, like a misfire. Everything else seems fine. I had a “good” set of coil packs that I removed from car when I first got it when I changed them over to new coils. I swapped out current ones for those, but no change. I also changed the plugs, no change. Seems to rev over 4 when out of gear with no load just fine no “misfire”, but as soon as its in gear with a load of any kind, it “misfires” as soon as rpm drop back below 4 k it runs perfectly, smooth, starts, restarts and drives fine as long as I keep it below 4 k while in gear. All readings look fine, no CEL   Any idea as to what could all a sudden cause an issue when pushing rpms passed 4 k?
    • When you say your cams are 272/262 is that 272in and 262ex?
    • We're arguing semantics. I am saying 45 accel and a 55 deccel ramp are "2 ways". Even a 45 degree ramp and an 89 degree ramp is "2 ways", because it is literally... two ways. The cusco 55/30 ramp is a 2 way. It's two ways. I get it though - in normal nomenclature a "2 way" would be 45/45 or 55/55 or 60/60 i.e the same locking in both directions. And something like 45/65 would be considered "1.5 way". I would then say if we're getting into the nitty gritty then every locking diff is a "2 way" diff and we should not speak in 1.5, or 2 ways but ramp angles instead. Which ofc if one of those ramp angles is 90deg, that side is not doing any locking. :p So Nismo don't obviously sell 3 things. The fact of the matter that they only sell two items really goes to show that there's a 2 way and a "1,5 way" which is really a 1 way. I believe the actual lockup for the 'adjustability' of the GT pro is really just setting preload for when the ramps actually start locking up. It's not changing how much 'wayness' there is. It is (somehow) horribly explained. People just buy whatever diff and go "locks up good bruh" and that's what ends up on socials forever.  
×
×
  • Create New...