Jump to content
SAU Community

Recommended Posts

I got the Aem progressive kit which has a fail safe and increases with boost depending how the controller is setup. Also got an inline water filter and was about 330 delivered from summit racing

Edit- looks like prices have gone up a bit :(

Edited by t_revz
  • 2 weeks later...

A mate rang me up and said he flipped and destroyed his sprintcar so I can have as much methanol as I want.

Maybe this will be enough to motivate me to get my exhaust done (which I now have all the parts for) and get retuned with water/meth :)

A mate rang me up and said he flipped and destroyed his sprintcar so I can have as much methanol as I want.

Maybe this will be enough to motivate me to get my exhaust done (which I now have all the parts for) and get retuned with water/meth :)

Bugger that, run it on straight methanol! :yes:

Seriously considering this as an option, we were looking at an e85 conversion but it was going into the $1000s by the time you uprate injectors, pumps, flex tune etc..

Is there a tuner in sydney with experience in this?

fitted a AEM 40 micron filter to my setup tonight..and shifted it all, its now pre-turbo, so will be interesting to see what it does

efficiency wise.

Doing another with a mate to his 3076 56T .64 ex gate on stocky mani in next week or so aswell, to tap out the turbo to its max, its already on

E85, just want to see how much more flow it can give turbo, we be interesting to see..

cheers

darren

Edited by jet_r31
  • 3 weeks later...

Well, I bought it, but after a rethink the money will lbe better spent on an EBC.

So it's for sale , check the FS section.

  • 2 months later...

just dynoed my car on 98 and then on water/meth injection

600cc CM7 coolingmist jet, added 10 degrees of timing across whole map, same as E85, it would have took more, but that was enough for me

20 degrees on 17psi to 30degrees

cheers

darren

Edited by jet_r31

Got an overlay to show results of before/after? Ignition changes only, or did you adjust fuelling too?

That's a significant amount of increased advance, hopefully should offer the same sort of torque increase offered on E85

  • 2 weeks later...

What kind of timing do you have after WM install ? I believe im +6 +4, some people tlak about 20.. so maybe I should ask my tuner to play more with timing ?

2) I have a CM7 injector from coolingmist installed in the intake, should I see a gain if I go direct port ?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Mixing things up - installed some leather recaros to match the leather seat covered rear seats. Interior looks pretty schmick now except for some slight wear on the steering wheel which I will monitor and address if it becomes worse or actually noticeable!  
    • Didnt realise RB's had more then 1 head.
    • I'm normally copping my own abuse from neglecting my daily drivers. "Those suspension bushes will last a bit more", "Don't worry about the oil leak, just keep topping it up". The project cars I'm always doing things slowly on them as I'm wanting them to be done better, and neater, and nicer. Luckily I don't have to deal with 18 year old Matt's "Learning to wire" stuff in the project cars. And there's only one piece of wiring I'm displeased about in the Landcruiser, and it's about to be cut out... However, the box loads of parts that have been going through this place lately for the Landcruiser... Brake pads Brake Rotors Full handbrake overhaul Wheel Bearings Seals Swivel hubs Steering Boxes Half the suspension joints Shocks Air bags (Ones to go in the rear springs for towing) Water pump Timing kit Lower timing case Harmonic Balancer Radiator Lots of other little seals and shits Gas struts for the bonnet New power window switches And god knows what else I've forgotten... Ha ha ha I have my fingers crossed the pinion seals don't start leaking on the diffs, that the transfer case doesn't leak, and the gearbox input shaft doesn't leak, nor the rear main seal. As they're about the only seals I haven't replaced in the driveline! I'm seriously eyeing off buying new caliper rebuild kits front and rear brake calipers... I'll probably recheck all the valve clearances soon too, and hopefully, it should be all good and sweet to haul some long distance trips again!
    • Every time I pull my 3x gauges out of the console and see the crack-addict way that I did the wiring, and I just can't bring myself to tear it all apart and "make it nice", because it is currently working. In fact, the last time I was in there I probably made it worse.
    • The best part is when you own the car long enough that you look back and find your OWN ham fisted amateur shit!
×
×
  • Create New...