Jump to content
SAU Community

Recommended Posts

Hi all,

I own an r34 gtt and am looking for an oil to use to suit daily driving and the odd track day. I live in Perth so it doesn't get that cold over here as well. If anyone could recommend what combination would be best ie 10w-50, 5w-40 etc it would be greatly appreciated !

Attached is some oils Supercheap sell. Any recommendations on what one to buy would also be great post-135000-0-56593000-1423492571_thumb.jpg

Thanks in advance

Link to comment
https://www.sau.com.au/forums/topic/453695-what-oil-viscosity-to-use/
Share on other sites

Also before anyone says search the forums I've seen lots of stuff on what brand of oil people use but not too much on the viscosity, but if someone finds a forum discussing this my apologies and could you please link me !

If you go to the track at all a full synthetic gives you a measure of extra protection.

There are lots of opinions about viscosity but I use Motul 300V 15W 40

If you have an oil pressure gauge and preferably an oil temp gauge as well you can see what works for you.

  • Like 1

For years I've persisted with using 10W-40 weight oil as I believe that's what's recommend. Using that weight I've always experienced a slight amount of oil misting out through the front of the engine (cam shaft seals etc). Several seal changes over the years and different cam breather setups never fixed the issue.

I recently changed to 15W-50 weight fully synthetic and the leaks appear to be gone.

  • Like 1

Given the usage model of your car you could realistically use just about any of those oils.

Given that Perth gets pretty hot and that you plan to do some track work and that it IS a turbo, avoid anything with a 30 rating. You need at least 40. If you tend to run the oil to high temperatures (do you even know how hot your oil gets?) then a 50 would be better.

Out of all that lot in the Supercrap listing, I would lean towards the Penrite 10 10ths or HPR10.

  • Like 1

Been using Penrite Racing 10 for 8 oil changes so far and I can't fault it.

My car runs an external oil cooler, so the oil temp is at 80° for most of the time.

Highest I've seen it get to is 100° after some prolonged spirited driving, but it gets down to 80° pretty quickly and oil pressure is stable from when it first goes in to when I change it at 5000kms. Ive been tempted to go longer between changes but its not overly expensive

Have used Motul, Mobil 1 in the past and the car feels happier. Tempted to try the Nulon synthetic at some stage also

I reckon ?W-40 is the best choice. AFAIK the only two valid reasons to go thicker are;

1. To bring oil pressure up to spec in a worn motor

2. To hack around running your oil too hot.

Instead of #2, get an oil cooler that will keep your oil below 120 Deg, and use a full synth 40.

Yeah I know but I have <2 weeks to do all this stuff to my car for the track day and adding an oil cooler isn't an option right now, but when I get the time I definitely will. And thanks for the suggestions guys. I was looking at the penrite 10w-50 oil before and I think I'll go with it for now until I get an oil cooler, then maybe I'll go for a 10w-40 oil or stick with the penrite depending on how it goes. Once again much appreciation for all the continuous help here !

R32 GT-R, 160k+ km (probably more), no oil cooler, two overheats with 5W-60 (like 130+°C oil temps), three track days. Motor sounds the same as it's always been, car runs fine :).

Ran a track day with Racing 10 as well, I think it runs better with that, but my car runs hot on the track.

Now that I have an oil cooler, I might switch back to Racing 10.

Each to their own I guess but if its a street car that is only doing the occasional track day then frankly as long as its a reasonable quality semi synth oil can you really drive a car that hard on the road that a 10W-40 or 15W-50 or thereabouts is going to be an issue?

When you do a track day, the 1-2 times a year ALWAYS put a fresh filter and sump of oil in the car. That't my practice. And frankly people saying run a cooler, keep it under 100deg....my experience is your oil temp will run over 100, more like 110-120deg c which is perfectly fine.

Remember that the oil going through/around the cams and lifters is subject to far less shear and temp and only running at half the speed of the crank vsgoing through the mains and big end so you are only measuring the average oil temp on your gauge.

The old wives tail , which seems to hold true on race cars is run the oil over 100deg c so any moisture/condensation, blow by gases etc dont stay entrained. How true that is I dont know...but of course those engines are purpose built and toleranced accordingly

So that is the BS I tell myself and every time I go to the track I always run a genuine Nissan oil filter and Castrol 10W60. I love the viscosity, rape my engine with boost and revs and havent lost a bottom end.

If you find on your aftermarket pressure guage you have 60psi at 7,000rpm with the oil up to temp with XX oil then I would be bumping up viscosity so that you are between 70-80psi

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Even more fun, leave all the ADAS stuff plugged in, but in different locations, hopefully avoid any codes!   And honestly, all these new cars with their weird electronics. Pull all the electronics out Duncan, and just shove an aftermarket ECU and if needed a trans controller in, along with a PDM. Make it run basic but race car styled!
    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...