Jump to content
SAU Community

Recommended Posts

52 minutes ago, emts said:

I think your overestimating a stock cars speed.. and under estimating it's reliability

 

Whilst a STI is very quick on a road a stock one on the track just does not have the tyres/suspension to be corning hard enough to really carry enough speed to cause a problem.

plenty of people run STI's on the track and they have no probs car mags run them all the time.

your just  going to do a few 200 -> 60 slow downs, and a set of brembos will handle it fine.

your not going to be pulling low 20's or anything.

monitor your temps adjust your tyre pressure during the day (I assume STI have TPS as the stock imprezza does) and you will be fine,

Sandown is normally 5 lap sessions I would be doing 2 hot 1 cool down and then 2 hot to finish (you then get a cool down coming into the pits)

couple laps of the pits and don't put the handbrake on in the pit.

you are going to have lots of fun.

That's exactly what I thought, the magazines hammer them all day without issues.

I'll keep you all posted anyway with what happens :D

I'm expecting pads to basically be gone and tyres go mooshy after a while. 

The car has giant front calipers it will be fine.

And also got that fluro green radiator ducting so extra cooling.
Will be fine. Maybe bring a hand held temperature gun to measure radiator temp/block temp after session.

  • Like 1

Contribution from my limited experience:

Brake early into turn one on your first flying lap to get a feel for it; people seem to underestimate how cooked their brakes can be coming onto the main straight. That huge kitty litter patch is there with good reason.

Flashbacks to Simons car going through kitty litter and ripping his FMIC apart ? 

Making me wanna just do motorcycle track days again, much cheaper :)

Edited by UNR33L
11 minutes ago, UNR33L said:

Flashbacks to Simons car going through kitty litter and ripping his FMIC apart ? 

Making me wanna just do motorcycle track days again, much cheaper :)

if your intercooler is hitting the kitty litter in a WRX/STI you have bigger problems.

 

so flash back to my first ever track day 

was with WRX club and was meant to be driver training, however I was only entrant so they just dumped me in with regular told me I was in a group with similar speed and just follow them. Note my car was very stock at time

 

first hot lap I was following a wrx to turn one saw his brake point so I hit it 50 meters earlier just to be careful...cue flying straight past corner and into kittly litter..one I finally slowed enough to know was not going hit wall look at mirror to see a MX5 flying backwards into the kitty litter right at me, so powered on out. no damage lucky.

 

went and tracked the WRX in the pits later, semi slicks, Big brake conversion and fully stripped out....damn it.

 

 

21 minutes ago, blah_blah said:

Anyone going to this?

If so come by and say hello ill be competing in Quake

 

 

Thought about it, I wouldn't mind running in the open forza competition with the v8sc

Not much else really takes my interest though

Edited by UNR33L
19 minutes ago, emts said:

if your intercooler is hitting the kitty litter in a WRX/STI you have bigger problems.

 

so flash back to my first ever track day 

was with WRX club and was meant to be driver training, however I was only entrant so they just dumped me in with regular told me I was in a group with similar speed and just follow them. Note my car was very stock at time

 

first hot lap I was following a wrx to turn one saw his brake point so I hit it 50 meters earlier just to be careful...cue flying straight past corner and into kittly litter..one I finally slowed enough to know was not going hit wall look at mirror to see a MX5 flying backwards into the kitty litter right at me, so powered on out. no damage lucky.

 

went and tracked the WRX in the pits later, semi slicks, Big brake conversion and fully stripped out....damn it.

 

 

 I think last track day I did in a car was 8 years ago Winton in my 33 gtr 

The centre caps on my wheels were plastic and melted off :(

What recording app do you use on phones?  I heard Racechrono is good? 

Edited by UNR33L
52 minutes ago, blah_blah said:

Ayyyy ill be there Saturday

I'll try and make it down, just saw there'll be 5v5 CS:GO in the main arena which should be good

I'm guessing the place is gonna be packed

Edited by UNR33L
2 hours ago, emts said:

racechrono on android with a external 10Hz GPS receiver.

 

+1 for this.

That said, have used WITHOUT gps receiver, still gets pretty good/usable/awesome data. Would try it on its own first nowadays with updated/modern phones.

6 hours ago, emts said:

if your intercooler is hitting the kitty litter in a WRX/STI you have bigger problems.

Yep.

First proper track day I did was Rexmas at Sandown.

Didn't kill brakes and tyres that day and it was only allowed to push it at 80% that day. But Platts managed to blew TMIC Y pipe and boost went from 18 to 25psi on 205 block...

1 hour ago, Count Grantleyish said:

Yep.

First proper track day I did was Rexmas at Sandown.

Didn't kill brakes and tyres that day and it was only allowed to push it at 80% that day. But Platts managed to blew TMIC Y pipe and boost went from 18 to 25psi on 205 block...

RIP

The more I read about the EJ the more I cringe 

I mean the Focus RS was the other option ? 

But the rumble is good!

Edited by UNR33L

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
×
×
  • Create New...