Jump to content
SAU Community

Recommended Posts

R32 GTR - Aftermarket Radiators and Factory Shorud

Hi All, 

 

Have been looking around and it seems some of those with aftermarket radiators have hacked up/no shrouds and others have them intact. Who here has a aftermarket rad with a factory shroud that fits?

Koyo radiator, factory fan and shroud. No touch. I also installed new radiator bushings and pulled them all the way forward on install. Worn bushings could have caused mine to hit. Another option would be to machine some offest bushings pulling the radiator further forward


14 minutes ago, bcozican said:

sometimes that chopping etc of the shroud/ rad from the fan comes from worn / broken engine mounts when the car brakes etc the engine can move forward hence closing the gap / changing the alignment of everything... been there !

Engine mounts maybe.  In my case and at least a couple of others I've seen it's simply the radiator getting sucked back towards the engine by the engine fan.  It doesn't seem to happen with stock radiators, so maybe they are just too thin (to take up the room) and too thin (to put up enough resistance to airflow) to move far enough against the rad mounts.

 

I just jammed some more rubber into my upper mounts (on the back side) to pre-load them and prevent it moving back.....well, after it has already sliced a line through my shroud!

nope, don't like their welds :)

but they're massive up your way, Ryan Tuerck uses them... if you're bored... go compare the welds on a Plazmaman FMIC and a Mishimoto :)

I've got a cefiro, so not a gtr. But, 

 

I run a 52mm rad with the stock shroud and fan. Had a few drama's with the fan hitting the shroud.

I machined some new lower bushes out of nylon, and made new brackets for the top with no bush.

 

Haven't had a issue since. Car is used for drifting so gets a bit of a thrashing. Tried twin thermo's early on, and they were shit.

Granted, they weren't expensive ones, but stock fan and shroud is simple, and it works.

 

Oh and don't underestimate how much the stock fans flex, I had a Z32 fan (greater offset, but had one lying around) on after the thermo's shat themselves , had a decent 15mm gap fan to rad and it still grabbed the radiator at high rpm.

What is the thickness of factory radiator?  Mishimoto is only 32mm so it should have fewer clearance issues, and 10% cheaper than Koyo here.  They also have great lifetime warranty that even covers collision.

1 hour ago, Dan_J said:

well i personally dont, but hey each to there own....

only if done right.. and 9/10 times it is done wrong...

Most owners just hard wire their fans OR use shitty fan controllers that turn off and on constantly like a strobe light.. followed by those who just hook it up to their OEM overheat fan relay/thermoswitch.

You need a proper fan controller either a standalone unit OR through your car's aftermarket ECU to set OFF and ON points followed by some form of hysteresis - only then would that be consider an appropriate installation.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Lock me in mate, although I'm not sure if I'll be heading up from Goulburn or down from Sydney, either way, return will be back to Goulburn 
    • Sounds good, we will aim to be there! @The Bogan I'll give you a shout if you are heading up to campbelltown for the meet too.
    • Before I get to the test day, just to finish off the android head unit. This is a demo from car start up....the standard/host system takes a few seconds to boot (same as all v37) but Android comes up quickly. In this vid I'm using the delivered launcher but have set the default to Agami since which is easier to navigate when if use primarily 5 apps. You can see the host system still takes over when required eg putting it in reverse, and you can switch between Android and not by holding the back button 3 sec. It is pretty responsive (fast) but you can see I had to press harder than expected a couple of times.  I still have the phone connected to the stock system, and that also seamlessly takes over Android music playing. v37-android-demo.mp4 The bigger reason that I put this in though is so that I can use Ecutek directly on the head unit. That gives me a dash with logging (up to 20MB only), high and low value warnings on any parameter etc etc. I've run a USB cable from the Ecutek OBD dongle to a USB input on the unit, easy. v37-ecutek-demo.mp4   The unit did freeze on the launcher the other day, I think Agami was trying to verify the license when it didn't have a data connection...will monitor and report back if there are any other problems but so far I'm very happy with the upgrade.
    • Nah that is just crappy GPS mapping, I did have a small excursion (cold tyres, damp track, surprise!), will post up that when I get a chance.
    • So 10/10 times that code is coil packs? I mean if that's the case ill drop the $400USD or so to replace them. I didn't know these cars threw codes before the issue became an issue.
×
×
  • Create New...