Jump to content
SAU Community

Recommended Posts

R32 GTR - Aftermarket Radiators and Factory Shorud

Hi All, 

 

Have been looking around and it seems some of those with aftermarket radiators have hacked up/no shrouds and others have them intact. Who here has a aftermarket rad with a factory shroud that fits?

Koyo radiator, factory fan and shroud. No touch. I also installed new radiator bushings and pulled them all the way forward on install. Worn bushings could have caused mine to hit. Another option would be to machine some offest bushings pulling the radiator further forward


14 minutes ago, bcozican said:

sometimes that chopping etc of the shroud/ rad from the fan comes from worn / broken engine mounts when the car brakes etc the engine can move forward hence closing the gap / changing the alignment of everything... been there !

Engine mounts maybe.  In my case and at least a couple of others I've seen it's simply the radiator getting sucked back towards the engine by the engine fan.  It doesn't seem to happen with stock radiators, so maybe they are just too thin (to take up the room) and too thin (to put up enough resistance to airflow) to move far enough against the rad mounts.

 

I just jammed some more rubber into my upper mounts (on the back side) to pre-load them and prevent it moving back.....well, after it has already sliced a line through my shroud!

nope, don't like their welds :)

but they're massive up your way, Ryan Tuerck uses them... if you're bored... go compare the welds on a Plazmaman FMIC and a Mishimoto :)

I've got a cefiro, so not a gtr. But, 

 

I run a 52mm rad with the stock shroud and fan. Had a few drama's with the fan hitting the shroud.

I machined some new lower bushes out of nylon, and made new brackets for the top with no bush.

 

Haven't had a issue since. Car is used for drifting so gets a bit of a thrashing. Tried twin thermo's early on, and they were shit.

Granted, they weren't expensive ones, but stock fan and shroud is simple, and it works.

 

Oh and don't underestimate how much the stock fans flex, I had a Z32 fan (greater offset, but had one lying around) on after the thermo's shat themselves , had a decent 15mm gap fan to rad and it still grabbed the radiator at high rpm.

What is the thickness of factory radiator?  Mishimoto is only 32mm so it should have fewer clearance issues, and 10% cheaper than Koyo here.  They also have great lifetime warranty that even covers collision.

1 hour ago, Dan_J said:

well i personally dont, but hey each to there own....

only if done right.. and 9/10 times it is done wrong...

Most owners just hard wire their fans OR use shitty fan controllers that turn off and on constantly like a strobe light.. followed by those who just hook it up to their OEM overheat fan relay/thermoswitch.

You need a proper fan controller either a standalone unit OR through your car's aftermarket ECU to set OFF and ON points followed by some form of hysteresis - only then would that be consider an appropriate installation.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My bad, I unplugged the one underlined in red instead of yellow before. With the car started, after unplugging the IACV (the one underlined in yellow), it idled at around 400/500 for 3 seconds before stalling. Attempting to start the car without the IACV will not start the car.   It does stutter and sputter for around 5 seconds before dying. However, immediately after starting it, you can already hear some slight sputters from the exhaust.   It won't start with the AFM unplugged. If it is when the car has already started, it stalls in a few seconds.   Yesterday, I did take some logs using Nistune of 3 scenarios. Car idling till it stalls Car idling and unplugging the IACV Car idling and removing the AFM I also have some previous logs of when the Car is idling till it stalls and when driving and it cuts. I am not really knowledgeable enough to understand what to look for. After every test, car idles rougher and rougher, until I have to stop. It will be fine the day after.
    • There is no difference between a 17x8 and an 18x8. The total diameter of the tyre needs to remain +/- the same (so you don't mess up the gearing, speedo reading, and clearance when turning front wheels..... so you just need to use a lower profile tyre on th 18 than you do on the 17. /rocket surgery.
    • I thought the same to start with. But then I thought it was one of those LCAs where the end of the ARB goes through a bushing in the LCA itself, instead of having an end link.
    • Yeah - I mean, go the other way. Smaller range. Not larger.
    • To re-cap, I bought: https://www.alibaba.com/product-detail/Lsailt-8G-Infiniti-Q50-Q60-2014_1601171829627.html?spm=a2756.trade-list-buyer.0.0.2cd476e9FTIlKE As you can see, if I bought 20 it was $653, but I bought 1 so it was $1,170. I was very tempted to buy 2 and resell 1 at 25% cheaper. @MBS206, I am not sure if they do a Kluger one, here is their list but it might be there under a global model name: http://www.lsailt.com/product/android-interface?page=1 Keep in mind these full android replacements have basically all the bits a phone does (cpu, ram, storage, wifi, bluetooth, usb interfaces) other than a screen (it uses a host), thus the $800+ cost. Android Auto screen mirroring is MUCH cheaper as it's just a cut down shell, input mirroring and output mirroring BTW I also need that "screen off" feature, it is much harder to see wildlife even if a dash is reasonably dark. Both the Fuga and V37 have display off buttons for night use, they just come back on for a second or 3 if you interact with it, eg skip a song.
×
×
  • Create New...