Jump to content
SAU Community

Borg Warner EFR Series Turbo's V 2.0


Piggaz

Recommended Posts

here you go guys. 

BW 8374 1,04

Built head with studs, gasket, springs blah blah

Stock bottom end

HKS 256 drop in cams

CRG split pulse manifold

e85 

504kw at 30psi. I told tuner to cap it at 30psi due to stock bottom end. Should see another 30-50kw with 4-5 more psi.

30psi around 4600rpm.

Its a little laggier than my mechanics (he gets 33psi by around 4400rpm), which I think could be due to having a massive 60mm old tech gate or perhaps due to it not being a built motor.

Still a bucket load off fun. Starts to wind up around 3k and really picks up boost 4k

Dyno run below and dyno sheet attached.

 

dyno.png

  • Like 2
Link to comment
Share on other sites

15 minutes ago, Sub Boy32 said:

I put a thread up asking the Mods to open up the EFR thread again......they just deleted my post.

 

Seen it. Half the reason why I made this.

  • Like 2
Link to comment
Share on other sites

Someone had to start it again, lets hope it does not get bogged down with BS ?

But it is hard to find info on the EFRs ?

I think because there are so many build types for Skylines now ranging from stock  to over 3.2Lt , it is also hard to have back to back comparisons.

But from what I can find out,  the EFR8374 will get me going quicker, with a much better transient response and roughly to the same top HP as my PT6266 Gen 2 ?

Hopefully some back to back comparisons :)

Link to comment
Share on other sites

Want to see comparison with -5's. LOL, only joking.

It would be good this time if the bullshit comments are kept to a minimum and maybe another thread started for bw only dyno results. Just so there's a place for chit chat and one for results. The old thread did lack results. Just a suggestion. Carry on[emoji106]

  • Like 1
Link to comment
Share on other sites

4 hours ago, usmair said:

here you go guys. 

BW 8374 1,04

Built head with studs, gasket, springs blah blah

Stock bottom end

HKS 256 drop in cams

CRG split pulse manifold

e85 

504kw at 30psi. I told tuner to cap it at 30psi due to stock bottom end. Should see another 30-50kw with 4-5 more psi.

30psi around 4600rpm.

Its a little laggier than my mechanics (he gets 33psi by around 4400rpm), which I think could be due to having a massive 60mm old tech gate or perhaps due to it not being a built motor.

Still a bucket load off fun. Starts to wind up around 3k and really picks up boost 4k

Dyno run below and dyno sheet attached.

 

dyno.png

Are you running E85?

Good to see this thread back in action!

 

  • Like 1
Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Both of those things are on my to do but not quite in a position to do that just yet until I can at least get it running back to stock. Going to work on getting the exhaust manifold gasket and studs replaced first, an obvious need it now. Then I'll try out the new maf and see hownthat does. After that I'm thinking cas if I'm still having the same issues. Still need to run the fuel out and refuel I'll change the fuel filter tomorrow along with cleaning the iacv with carb cleaner. If all else fails I'm going to get a serial port and see if I can get some sort of data on what the ecu is seeing when the issue is happening but really hoping one of the methods above work out first. After I get a good base I'm going link but have to save for that so it'll be a while for that based on my tuners suggestions. Definitely need the exhaust leak fixed first though car has always fallen flat after about 4-4500 rpm since I've had it and suspecting that's the issue. Then I can move forward with the rest. 
    • My vote is rebuild s2 engine or maybe get a neo (but expect you may need to rebuild that too). Doing an engine conversion you would have to be a true tragic nowadays and actively be aware there's better/smarter options for value.
    • Or buy one someone built earlier! (realistically V8 mustangs or MKV supras are great). I see people nowadays putting ZF8's into MK4's, and people putting 370z gearboxes, diffs, axles into R and S chassis and it's like.... just get a 370z at that point and mildly boost the 3.7 instead of the 2L and away we go...
    • If you're going to go v8 or really any swap now with all the tax, I'd most likely just get rid of the car and start with something else. Unfortunately, I have a mate with a surplus of ls and Ferrari/Maserati v8's that's always tempting me FFS lol.
    • If you can get a clean, tested neo from Japan for $3500 these days, it's probably worth getting either way, hard not to be skeptical at that price. Otherwise probably rebuild the s2.
×
×
  • Create New...