Jump to content
SAU Community

Recommended Posts

G'day ppl could I get pointers on a full rebuild of anRB@% GTST Series II engine for 500 to 1000 hp. I'm after horsepower and reliability together I dont want to be breaking somthing all the time lol. How much roughly could the rebuild cost aswell rough figures of what other ppl have spent and the ideas aswell would be helpfull. Im also south of brissy qld so any shop recommendations would be greatfull to.

For a start go to the Forced Induction section and look at the RB25 turbo upgrade thread. You will see what people have done to their cars to get more power. Start at the end to avoid a load of outdated gear.

And there is a huge difference both in power and in money between 500 and 1000hp so have a think about how much power you really want.

  • Like 1

Estimate at $40k to get everything going reliably 

im guessing u will be paying a workshop as u if you knew what u were doing u wouldn’t be asking such a vague question 

LOL, reliability for what use?

Dyno queen

Street car

Track hack

Sprints

You need lots of cubes, lots of strong parts, and some boost.

What transmission and drivetrain you using, that stuff can start eating itself at 400hp, let alone being reliable at 500-1000hp, for "some" reliability I would budget around 60-80k, easy, maybe more.

Your also going to need a "spare stash of cash" for when your "reliable setup" breaks.

And it will.

  • Like 2
On 5/28/2020 at 4:53 PM, Ben C34 said:

What can you do? Cmon man, this thread is ultra vague!

Well at the moment mate I'm rebuilding a LS3 engine out of a senator from ground up and my skyline is my next project I was just seeing what other people thoughts were hoping there was people on here to throw out ideas I might not have thought of

On 5/28/2020 at 5:26 PM, mlr said:

LOL, reliability for what use?

Dyno queen

Street car

Track hack

Sprints

You need lots of cubes, lots of strong parts, and some boost.

What transmission and drivetrain you using, that stuff can start eating itself at 400hp, let alone being reliable at 500-1000hp, for "some" reliability I would budget around 60-80k, easy, maybe more.

Your also going to need a "spare stash of cash" for when your "reliable setup" breaks.

And it will.

Cheers bro I'm setting up for street n track I been researching and I'm just going to aim for 500hp I'm going to run a 6 speed manual transmission and I can apparently get a 9 inch diff made 

23 minutes ago, MrSINNER said:

Cheers bro I'm setting up for street n track I been researching and I'm just going to aim for 500hp I'm going to run a 6 speed manual transmission and I can apparently get a 9 inch diff made 

Nothing wrong with the RB diff.

50 minutes ago, KiwiRS4T said:

Nothing wrong with the RB diff.

Really mate I haven't really had much to do with the RB parts as a whole I been into more V8's but I am really loving the RB's. I have seen the limited slip upgrade for them is that the better way to go?

33 minutes ago, MrSINNER said:

Really mate I haven't really had much to do with the RB parts as a whole I been into more V8's but I am really loving the RB's. I have seen the limited slip upgrade for them is that the better way to go?

Kaaz 2-way into the centre and off you go :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Fark what are the changes of that snapping like that, clean. Nek minnit, custom radiator goes in, with built in oil cooler like those discontinued PWR ones from yesterdeacades ago
    • I thought I'd do a write up on an auto transmission fluid change for a the nissan 7 speed Automatic. At some stage the genius engineers decided that the fluid in the trans was "for the life of the transmission", (which seems kind of self supporting to me) and removed the dip stick and fill tube (funnily enough there is still a casting for it). Anyway, for this job you do need 2 specialist tools in addition to regular hand tools, jack and good chassis stands. You need a way to pump fluid up to the transmission; I got one of these but there are plenty of other options: https://www.ebay.com.au/itm/364584087070 Don't trust the generic listing though, it does not come with the required adapter for the Nissan 7 Speed. You need one of these, can't do the job without it: https://navarapart.com.au/product/genuine-nissan-patrol-y62-d23-np300-navara-re7-dipstick-fill-connector1 You need a heap of compatible transmission oil. Could be Nissan, could be anything else rated for Nissan Matic S. You need at least 10 litres, I had 15 to give it a better flush... Also, you need some biiig oil catch trays, at least one of these, or bigger if possible (volume was fine, size was very marginal): https://autobarn.com.au/ab/Autobarn-Category/Tools-%26-Garage/Specialty-Tools/Oil-Service/Garage-Tough-Oil-Drain-Pan-Black-16L---GT1068/p/TO03191 Finally, a measuring jug is very useful if your pump does not have volumes marked on it, I got a 6l one: https://www.repco.com.au/oils-fluids/fluid-accessories/measuring-jugs/penrite-measuring-jug-6l-pmj006/p/A5322648 Oh, and gloves.....this stuff is horrible (not as bad as diff oil, but getting there) ....First, jack up your car.....
    • So I mentioned the apprentice, @LachyK helped take the bonnet off. We just undid the nuts on the hinges and unclipped the gas struts, then pulled the bonnet back a little as the front was catching on the front bar.  I had a good look at everything today and have removed the rams, repaired/reset the hinges and bolted it back together like it never happened. I'll do a separate write up on the repair, and I also removed the poppers from the Fuga today too to save grief down the road.....as said above it is at least $5k to repair retail. I'm also happier about my ability to prepare a race car, and less happy about Nis-nault's engineering (I can hear @GTSBoy sAfrican Americaning) because the top hose of the radiator didn't slip off.......it snapped clean off. By practice I put the hose clamp hard up against the flare on a neck to make it least likely to ever move (thanks @Neil!). I guess that puts a little more pressure on the end of the pipe as it is further away from the rad, but still, that is pretty shit. I've put it back on for now as there was a fair bit of neck still there, but obviously there is no lip on the neck any more so I don't think I'll track it again until I have a new rad. Speaking of which....more research required. It looks like Koyo makes a standard size radiator in ally which I'll grab in the meantime, but I really want something thicker so might have to go custom in the medium term (ouch) Coolant still needs a refill and I have the pressure tester on it over night, but other than a wash down of the engine bay it seems alright. And @MBS206 noted something noisy on the front of the engine and I think I agree....time for a new accessory belt and tensioners I think.
    • our good friends at nismo make a diff for it, I have one (and a spare housing to put the centre in) on the way. https://www.nismo.co.jp/products/web_catalogue/lsd/mechanical_lsd_v37.html AMS also make a helical one, but I prefer mechanical for track use in 2wd (I do run a quaife in the front, but not rear of the R32)
    • What are we supposed to be seeing in the photo of the steering angle sensor? The outer housing doesn't turn, right? All the action is on the inside. The real test here is whether or not your car has had the steering put back together by a butcher. When the steering is centred (and we're not caring about the wheel too much here, we're talking about the front wheels, parallel, facing front) then you should have an absolutely even number of turns from centre to left lock and centre to right lock. If there is any difference at all then perhaps the thing has been put back together wrongly, either the steering wheel put on one spline (or more!) off, and the alignment bodged to straighteb the wheel, or the opposite where something silly was done underneath and the wheel put back on crooked to compensate. Nut there isn't actually much evidence that you have such a problem anyway. It is something you can easily measure and test for to find out though. My money is still on the HICAS CU not driving the PS solenoid with the proper PWM signal required to lighten the load at lower speed. If it were me, I would be putting either a multimeter or oscilloscope onto the solenoid terminals and taking it for a drive, looking for the voltage to change. The PWM signal is 0v, 12V, 0V, 12v with ...obviously...modulated pulse width. You should see that as an average voltage somewhere between 0V and 12V, and it should vary with speed. An handheld oscilloscope would be the better tool for this, because they are definitely good enough but there's no telling if any cheap shit multimeter that people have lying around are good enough. You can also directly interfere with the solenoid. If you wire up a little voltage divider with variable resistor on it, and hook the PS solenoid direct to 12V through that, you can manually adjust the voltage to the solenoid and you should be able to make it go ligheter and heavier. If you cannot, then the problem is either the solenoid itself dead, or your description of the steering being "tight" (which I have just been assuming you mean "heavy") could be that you have a mechanical problem in the steering and there is heaps of resistance to movement.
×
×
  • Create New...