Jump to content
SAU Community

Recommended Posts

I run a 2way full time. All comes down to have you like your set up to be. I’m a little happy on the track with front brake bias high and steer with the rear. If you don’t like the rear being a little loose on corner exit just run a stock lsd and you will be fine

Time attack/track work I would personally go with a 1/1.5 way only.

I have a 2 way KAAZ LSD and I can say that driving my friend's car with a 1.5 way around a technical track, it's actually faster than mine with a 2 way.

The thing is, all 1 ways, 2 ways, 1.5 ways etc are all 2 ways, just with different ramp angles.

If you want to go down the rabbit hole, go asking for ramp rate specs on diffs. Nismo actually only make a 1 way and a 2 way diff.

I'd wager that's the same for most manufacturers.

The "1.5 way" people are talking about is likely the 1 way, i.e the 45/90 ramp diff. (45 accel, 90 decel). My old "2 way" diff was also a 'real' 1.5 way with ramp angles of about 45/60.

Are other 2 ways true 45/45 '2 way' diffs? You'd have to ask. As for what is best... well, it really depends a lot of your driving style.

Depends on which cam is selected.

kaaz-adv-5-711x400.jpg?resize=711%2C400&+

image.png.a5e406d3f3105de9383648936262b26e.png

 

I definitely can say my 2 way KAAZ looks like this (actual photo of my diff)

image.thumb.png.a2c438551d755822b16e52161fda727e.png

 

and my mate's 1.5 way looks like the below (not his photo)

image.png.e546888de035199f8d9a58ce4c9c772a.png

 

 

 

 

  • Like 5

For what it is worth the Nismo 1.5 way I have is so fkn tight it may as well be a two way.  Shits me to tears it does. Clunkety clunk clunk.

It isn't just the ramp angle that is key here.  The amount of preload on the clutch packs before you add the motors torque is also important.  Get much of that and the diff will be an annoying clunkfest.

@admS15That looks like a 1.5 way. Assymetric ramp angles.

What djr said is correct. The ramps define how much of the locking power is applied on accel and decel, (ie 1, 1.5 or 2 way) and the rest of the diff (the number of clutch plates, springs etc) in the mechanism define the breakaway torque. You can make a 2-way diff with low breakaway torque that will behave nicely without clunking, but it will open up earlier than you might like. Or you can make one that might as well be welded. Cusco have a range of different diffs that cover that span and some even offer adjustment of how tighjt they are.

  • Like 1
11 hours ago, Dose Pipe Sutututu said:

and my mate's 1.5 way looks like the below (not his photo)

image.png.e546888de035199f8d9a58ce4c9c772a.png

 

This is a 1 way 😛

Good example though! 😛

but yes when selecting a diff.. "1 way" or "1.5 way" or "2 way" is very much like "Stage 1 turbo". There's not really enough information there.

I guess they key point is, you don't want/need a diff that locks the wheels together under deceleration as that promotes understeer on turn in. If you are buying, preference should be 1 > 1.5 > 2.

Having said that the GTR (non 33 vspec) factory diff is a mechanical 2 way and can be readily shimmed for the level of carpark clunking you want, That's all we use in the race car and it is a good thing, thanks Nissan.

49 minutes ago, ERO54N said:

Hey guys,

Just wondering what the benefits of an open diff are when compared to any sort of LSD on track? Genuine question.

 

When you've binned your car and one wheel/hub is completely seized but you want to try drive it back to the pits.

 

  • Like 2
  • Haha 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
×
×
  • Create New...