Jump to content
SAU Community

Recommended Posts

With high EBC loading, the boost pressure before cooler rises, but what inside inlet manifold doesn't change. Here's some thing fun to watch. Our TD06SL205 turbocharger on a CA18det pulling 307rwkws E85 fuel. Run 11 sec quarter:

Eastern Creek video footage from Sxxreco, Unopened Rb25det, using our 21U high flowed turbocharger making a super responsive 310rwkws on E85 fuel:

  • Like 2

Gday guys, I just wanted to post up quickly my results from a hypergear op6 hiflow on my R34. It was tuned by Trent at mercury and made 265rwkw @19psi on pump 98. Very pleased with the result, the power delivery is nice and smooth but still kicks you in the ass once it gets going ;)

Cheers!

updating some 1JZ results. Those are from 1JZGTE Chasers:

This is 292rwkws on 19psi on our TD06SL205 Turbocharger externally gated, P98 fuel, Unopened engine:

sl2051jz292rwkwp98.jpg

And this is using a high flowed factory CT15B on E85 fuel making 321rwkws.

ct15bhf321rwkwe85.jpg

Can you machine the TD06L2 (61mm) exhaust housing to take the larger TD06 turbine (65mm)?

Its been a few weeks getting the new test car ready and I've spent quite some time diagnosing a boost ceiling issue.

For today's test, I've tapped two extra boost sources on both sides of the intercooler piping, and monitored pressure drops on all four points.

nipples.jpg

Surprisingly it is a issue with the actual intercooler it self. Three intercoolers was tested, they were the Takashi (a good Chinese made cooler) in 600x300x68mm, 600x300x100mm, and a Generic ebay cooler in 600x300x76mm. Final result reviews the 600x300x100mm Takashi cooler had the best response, while the Generic ebay cooler made the most power.

boostall.jpg

powerall.jpg

I will likely be trailing a PWR item of a similar size, hopefully an expansive branded item could solves this issue.

Final result was peek of 281rwkws @ 19psi after cooler pressure on Pump 98 fuel.
ATR43SS-2 Internally gated
ID 1000cc injectors
Walbro fuel pump
Adaptronic Plug in ECU
3inches turbo back exhaust
Tune at Chequrered Tuning.

The last sheet shown the same turbocharger working with same type of engine but return flow cooler kited. Notice lag created of having extra piping length.

vsreturnflow.jpg

For best result on a Rb25det R34, Get a proper FMIC kit with a big free flow intercooler.

So that graph above shows a difference of around 750rpm extra "lag" with return flow pipework?

Is this a pretty typical result?

I run custom return flow style pipework, with 2.5 inch pipes and a pretty tight radius off one end of the cooler. Have been wondering for a while if any gains were to be had from going a traditional front mount style pipes.

My setup is laggy, but I think thats more to do with the turbo choice, and RB20 haha.

Would be interesting to see how a top mount setup might go seeing as you could really reduce the length of the piping. Don't know how you would go about fitting one for practical use but would be good to see what it could do on a dyno for some giggle factor.

  • Like 1

Nope, it's a daily so not necessary. The water radiator is quite large though, almost the size of the radiator and is sandwiched between the air con condenser core and the radiator for stealth. I haven't got around to logging temps properly yet (there are temperature senders in the top and bottom of the radiator and I will be placing them in the intercooler outlet too) but using an infrared temperature gun shows the IC outlet temps stay close to ambient on the dyno.

Throttle response is instant in every sense of the word as expected from a stock 21U turbo on a 30DET with an automatic gearbox. It'll be getting one of your highflows hopefully later in the year once a few other mods get done, most likely OP6 based.

Nice, I will be looking forward to your job.

In this car I'm mainly looking into some common mods that majority of people use, and this definitely shares to some of the problems that few people experienced, especially in the cheap and stealth category. I will be looking into possible ways of targeting those problems through a turbocharger.

Here is some thing fun to watch. :D

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • That's actually encouraging to be honest. my motor was rebuild many years ago but it's probably done less than 30,000kms and fucc all limiter or drift, majority street / drag / roll racing. It'll be fine 💪🏼 I don't even have lines or a can for the cam breathers installed yet, there is zero oil residue or splatter on or around them, it drives beautifully so it seems healthy. Just a ticky lifter, yet they're almost brand new oem genuine Nissan and haven't done many kms at all...
    • Have you confirmed the throttle body goes to WOT (and stays there) during the run?
    • I'm having a problem. I think it was mentioned above somewhere but can't see it.  I'm stuck in the cycle of, sand, filler, low spot again, put filler, sand, low spot again, now i put filler again and a thicker portion which seems to have helped but I got low spots in other areas. In the image. Circled in red thats where the original low spot was and the shape is the same as the red out line. I've more or less fixed that (still low spot up the top but now I have low spots where the green circled part is.  Is likely the issue that I didn't start with a course sand paper? I sanded the filler with 240 to reduce the risk of not going to far but maybe the issue is that I'm only taking off enough material to remove some of the filler but not the high spots. I now started sanding with 120 and I think I'm seeing a difference. I did fix one dent the other 2 are f**ked and seems like I made another low spot which is indicated by the furthest green circle on the left handside. Any thoughts and solutions?   Also second image. All of these rock chips, can they be filled in with primer or do i need to fill them all with filler/putty? So many rock chips on mine lol.
    • Well, I had an Edward Lee's special edition odo windback car/motor with a RB25DET S2 and I put down 372kW with a good amount of track abuse for 1.5 years before the ring lands decided it didn't want to stick around anymore 🥲 But probably didn't help I kept on smashing try limiter on the track and a few skid pans.
    • That is correct,  I have a forged RB25/30det NEO hiding away safely and I wanted to use the very rare greddy vct adj cam gear on this new setup and so I just used the whole thing on my s1 instead of pulling it appear because I'm lazy af 😅🤌🏼
×
×
  • Create New...