Jump to content
SAU Community

Recommended Posts

They seem to be really good so far!

They're from Pro Rack

S-Wing Flush 950

Part Number: S5

Fitting Kit

Part Number: K528

I got them through roof rack superstore.

what did they set you back mate?

$350 fitted.

I didn't actually look at how much you could get them online, because I do a fair bit of work for the roof rack place I got them from. I assumed they at least kind of looked after me.

My leather seats arrived!! Now to fit them. I thought they might be plug and play with my RS Four S, but I was wrong. Has anyone put leather seats into a Stagea that didn't originally have them?

  • Like 1

Yes, and they were plug and play. But that was S1, do S2 have something extra like seat heaters? If so you need switches if they are not on the seat, and considering the power they could draw I'd probably run separate wiring too. Or you could just leave them unplugged and worry about it closer to winter...

Leather seats are installed!

First attempt: I was using the same power supply as one of my amps. Went well until I tried to start the car, and I killed a few Eng Cont fuses in the engine bay. Try again.

Second attempt: I ran the positive from the 12V cigarette output to the seats and the car started like a boss.

post-51740-14474128399648_thumb.jpgpost-51740-14474128491649_thumb.jpgpost-51740-14474128595224_thumb.jpg

So thank you to everyone who gave me some ideas on how to do this. Now to clean up the old RS4S seats and sell them.

  • Like 1

Riding this pile of monstrosity from the Stagea.

20151115_122039%20%281024x576%29.jpg

Utter disgusting install. Not even the bin is worthy of this crud.

wow, surely that was not all part of the install for the hu ?

finally my rear wing fly to Aus today.

fitting easily, gain 100hp :nyaanyaa::nyaanyaa:

attachicon.gifIMG_1502.JPG

attachicon.gifIMG_1503.JPG

attachicon.gifIMG_1507.JPG

attachicon.gifIMG_1509.JPG

looks great ! think you accidentally a 0 there ;)

Riding this pile of monstrosity from the Stagea.

20151115_122039%20%281024x576%29.jpg

Utter disgusting install. Not even the bin is worthy of this crud.

This looks exactly like the pile of shit i pulled out of mine. There was over 15kg of old wiring that was not connected to anything at either end!

  • 2 weeks later...

Got to take a look at my M35 tonight.

Something very cool about being under the hoist looking at the manual box in place. It looks kinda bare now with all the AWD bits and auto missing :P

New radiator on, 6pd box in place, braided lines and wiring to be sorted tomorrow or late tonight i assume. All things pointing towards trying to turn the key hopefully this week. Tail shaft however probably won't be in till early / mid next week which is fine as other jobs are still needed (centre console / handbrake etc)

  • Like 4

Got to take a look at my M35 tonight.

Something very cool about being under the hoist looking at the manual box in place. It looks kinda bare now with all the AWD bits and auto missing :P

New radiator on, 6pd box in place, braided lines and wiring to be sorted tomorrow or late tonight i assume. All things pointing towards trying to turn the key hopefully this week. Tail shaft however probably won't be in till early / mid next week which is fine as other jobs are still needed (centre console / handbrake etc)

Pics not loading...

  • Like 5

This week I drove the S1, RS4 to Sydney and back. 1100k all up. I have had it for nearly ten years.And has 198 on the clock. Looked after but not pampered. A proper work horse.

It is really the first long trip I have done in it. Never missed a beat the whole trip. Was driven hard and gave 520 per tank. And was so comfortable even on the 11 hour o/nite trip down.

  • Like 1

Not so much a what have I done but a what I will do when the wife and kids give me 5 minutes of peace!

post-135423-0-54699400-1448750286_thumb.jpg

Next on the list will be coilovers, looking at MCA, Blitz ZZ-R and BC BR RS.

Anyone running the Blitz or MCA or anything else they are happy with?

  • Like 2

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
    • Hi,  Just joined the forum so I could share my "fix" of this problem. Might be of use to someone. Had the same hunting at idle issue on my V36 with VQ35HR engine after swapping the engine because the original one got overheated.  While changing the engine I made the mistake of cleaning the throttle bodies and tried all the tricks i could find to do a throttle relearn with no luck. Gave in and took it to a shop and they couldn't sort it. Then took it to my local Nissan dealership and they couldn't get it to idle properly. They said I'd need to replace the throttle bodies and the ecu probably costing more than the car is worth. So I had the idea of replacing the carbon I cleaned out with a thin layer of super glue and it's back to normal idle now. Bit rough but saved the car from the wreckers 🤣
    • After my last update, I went ahead with cleaning and restoring the entire fuel system. This included removing the tank and cleaning it with the Beyond Balistics solution, power washing it multiple times, drying it thoroughly, rinsing with IPA, drying again with heat gun and compressed air. Also, cleaning out the lines, fuel rail, and replacing the fuel pump with an OEM-style one. During the cleaning process, I replaced several hoses - including the breather hose on the fuel tank, which turned out to be the cause of the earlier fuel leak. This is what the old fuel filter looked like: Fuel tank before cleaning: Dirty Fuel Tank.mp4   Fuel tank after cleaning (some staining remains): Clean Fuel Tank.mp4 Both the OEM 270cc and new DeatschWerks 550cc injectors were cleaned professionally by a shop. Before reassembling everything, I tested the fuel flow by running the pump output into a container at the fuel filter location - flow looked good. I then fitted the new fuel filter and reassembled the rest of the system. Fuel Flow Test.mp4 Test 1 - 550cc injectors Ran the new fuel pump with its supplied diagonal strainer (different from OEM’s flat strainer) and my 550cc injectors using the same resized-injector map I had successfully used before. At first, it idled roughly and stalled when I applied throttle. Checked the spark plugs and found that they were fouled with carbon (likely from the earlier overly rich running when the injectors were clogged). After cleaning the plugs, the car started fine. However, it would only idle for 30–60 seconds before stalling, and while driving it would feel like a “fuel cut” after a few seconds - though it wouldn’t fully stall. Test 2 – Strainer swap Suspecting the diagonal strainer might not be reaching the tank bottom, I swapped it for the original flat strainer and filled the tank with ~45L of fuel. The issue persisted exactly the same. Test 3 – OEM injectors To eliminate tuning variables, I reinstalled the OEM 270cc injectors and reverted to the original map. Cleaned the spark plugs again just in-case. The stalling and “fuel cut” still remained.   At this stage, I suspect an intermittent power or connection fault at the fuel pump hanger, caused during the cleaning process. This has led me to look into getting Frenchy’s fuel hanger and replacing the unit entirely. TL;DR: Cleaned and restored the fuel system (tank, lines, rail, pump). Tested 550cc injectors with the same resized-injector map as before, but the car stalls at idle and experiences what feels like “fuel cut” after a few seconds of driving. Swapped back to OEM injectors with original map to rule out tuning, but the issue persists. Now suspecting an intermittent power or connection fault at the fuel pump hanger, possibly cause by the cleaning process.  
×
×
  • Create New...