Jump to content
SAU Community

Recommended Posts

Unfortunately the new custom sump was modelled on an R33 and it didn't clear the swaybar enough when we put it in last week.

Because of this we missed out at PI on the weekend. I had brand new rubber on the thing and was ready to go but no such luck...

Turns out that the whiteline sway bar that is on my car was a prototype from years ago and they don't sell them anymore so pretty unique situation. The bend is very close to the sump so that's what has caused the issue. I think that a new 27mm sway bar with a better option that pulling the sump off again! Custom one being investigated now. Hope it makes the 21st!!

  • 2 weeks later...

time for another update...

New 27mm swaybar has just arrived to solve the sump clearance issues. I currently have a loan 24mm until I get a chance to fit the 27mm. Might try both on the weekend if I can as a comparison.

Fulcrum suspension have sorted out the bar for me.

I've extended the wing end plates as the old ones were a little small and the bigger ones should hopefully stop a bit of the spill over the sides.

post-10715-0-12315400-1342526396_thumb.jpg

The splitter has come a long way. I'm still testing as it's all a bit new to me still. I'm really just copying what the fast guys do and following basic principles and advice I'm getting along the way.

I'll be logging the data at Philip Island this weekend to see if straight line speed is sacrificed and if corner speed is increased. As a bare minimum I'm expecting more downforce from just the splitter seperating the air and minimising air flow under the car.

If it all works the plan is to make the parts out of carbon fibre down the track. It's all trial and error at the moment.

post-10715-0-15594600-1342526630_thumb.jpg

post-10715-0-67829500-1342526762_thumb.jpg

post-10715-0-83309300-1342526985_thumb.jpg

loving the alloy canards. i made some about 3 years ago and was laughed at. been hesitant to make any new ones.

i seen in a build thread for an american R35 time attack car they made canards out of alloy. they were far easier and cheaper and did the same job.

are the uprights for your wing an off the shelf item?

Yeah the ally is pretty light except for the splitter. It's damn heavy. CF would be so much better

are the uprights for your wing an off the shelf item?

Nah they were made by superleggera carbon fibre in sydney. They're pretty hard core!

Yeah the ally is pretty light except for the splitter. It's damn heavy. CF would be so much better

Nah they were made by superleggera carbon fibre in sydney. They're pretty hard core!

oh they look like a production type thing.

do you have any bracing under the boot lid? i may have missed it.

Hope you don't mind Russ. Most people probably know what happened already!

Russmans R32 GTST blasting around PI in it's last shakedown before WTAC!

For the full article check out Autocult -> CLICK HERE!

7629603330_b9209c015b_b.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • To follow up a question from earlier too since I had the front bar off again (fking!) This is what is between the bumper and the drivers side wheel And this is the navigator side, only one thing but its a biggy! So basically....no putting coolers in the wheel arches without a lot of moving other stuff. Assuming I move to properly race prepping this car I'll take that job on and see how the computers respond to removing a whole bunch of ADAS modules
    • So I prepped the car for another track day on Wednesday (will be interesting to see coolant temps post flushing out and the larger reservoir, with a forecast of 3-14 being 20o cooler than last time I took it out). Couple of things to mention; since I am just driving the car and not taking a support vehicle, I took the rear seats out and just loaded the back up Team Trackday style. Look at all that space! To cover off removing the rear seat....it is weird (note the hybrid is probably different because it wouldn't have folding rear seats) Basically, you remove the lower seat base, very similar to a r series but it is a clip that pulls forward to release the base rather than it being bolted down. Easy Then, you need to remove the side section of the rear seat on each side. There is a 14mm head nut at the bottom of the side piece, the it slides upwards off a hook at the top to release; you also need to unhook the seatbelt from the loop at the top. Then the centre piece is weird. You need to release/fold the seats forward with the tab in the boot on each side From there, there are 2,x12mm headed bolts holding the rear of each seat to the folding bracket, under the trim between the rear seat and the boot (4x christmas tree clips there, they suck). The seat is out but you can see where the bolts attach to the bracket
    • As discussed in the previous post, the bushes in the 110 needed replacing. I took this opportunity to replace the castor bushes, the front lower control arm, lower the car and get the alignment dialled in with new tyres. I took it down to Alignment Motorsports on the GC to get this work done and also get more out of the Shockworks as I felt like I wasn't getting the full use out of them.  To cut a very long story short, it ended up being the case the passenger side castor arm wouldn't accept the brand new bush as the sleeve had worn badly enough to the point you could push the new bush in by hand and completely through. Trying a pair of TRD bushes didn't fix the issue either (I had originally gone with Hardrace bushes). We needed to urgently source another castor arm, and thankfully this was sourced and the guys at the shop worked on my car until 7pm on a Saturday to get everything done. The car rides a lot nicer now with the suspension dialled in properly. Lowered the car a little as well to suit the lower profile front tyres, and just bring the car down generally. Eternally thankful for the guys down at the shop to get the car sorted, we both pulled big favours from our contacts to get it done on the Saturday.  Also plugged in the new Stedi foglights into the S15, and even from a quick test in the garage I'm keen to see how they look out on the road. I had some concerns about the length of the LED body and whether it'd fit in the foglight housing but it's fine.  I've got a small window coming up next month where I'll likely get a little paint work done on the 110 to remove the rear wing, add a boot wing and roof wing, get the side skirt fixed up and colour match the little panel on the tail lights so that I can install some badges that I've kept in storage. I'm also tempted to put in a new pair of headlights on the 110.  Until then, here's some more pictures from Easter this year. 
    • I would put a fuel pressure gauge between the filter and the fuel rail, see if it's maintaining good fuel pressure at idle going up to the point when it stalls. Do you see any strange behavior in commanded fuel leading up to the point when it stalls? You might have to start going through the service manual and doing a long list of sensor tests if it's not the fuel system for whatever reason.
×
×
  • Create New...