Jump to content
SAU Community

Recommended Posts

  • 4 weeks later...
  • Replies 217
  • Created
  • Last Reply

Top Posters In This Topic

Hi, im after coilpacks to fit a 1998 ER34 Skyline 25GT RB25DE Neo, Does the YJ-RB2025-N fit? Was also wondering on return policy.

  • 3 months later...
  • 1 month later...

Hi, I was just wondering what the go was with RB25 *NEO* coilpacks these days, as when I was looking a few years ago, they weren't available - only blue ones were available :)

There was a brand, I think they were red, which sold NEO replacements for a short time but then withdrew them because there were problems.

I notice there are part numbers for NEO now though in the Yellow Jacket range so I take it we have a less expensive option for RB25DET NEO at last?

cheers

DaveB

Gday Dave. I have had YJs to suit the NEO engines on the market for around 3-4 years now.

They are $430/set including express delivery and come with a 2 year warranty.

Payment details sent via PM.

:cheers:

  • 1 month later...
  • 2 weeks later...
  • 4 weeks later...

Hey, I was just wondering if these have been tested on a vq25det? (2001 M35 Stagea). I have heard that although the same part no. the VQ35 coil packs arent powerful enough for the vq25det?

If good news, I will place an order this afternoon! :)

Cheers,

Corey

  • 1 month later...
  • 3 months later...

Just got some for my R33

Thanks to Paul for the great customer service

Thanks very much. I appreciate the business. :cheers:

  • 7 months later...

Along with our complete range of coilpack harnesses to suit the RB, SR and CA engines. We now have LS2/LQ9 to RB25(S1), RB25(S2), RB20 and RB26 plug and play conversion harnesses in stock.

That's right....no more butchering up your old harness to fit a set of LS coils to your RB engine.

Coming soon........... complete LS coilpack upgrade kit which will include a new set of Yellow Jackets LS2 coils, a new Wiring Specialties conversion harness and thanks to OTAKU GARAGE, we will also have a custom fabricated bracket to mount the coils all nice and tidy. We will also be offering custom powder coating to the brackets in the colour of your choice if you so desire....

Check out the PW website for more info or to purchase the coilpack harnesses - http://www.performance-wise.com.au/wiring-specialties/coil-pack-harnesses

  • 2 months later...

In need of a fresh 6 pack! Just put my order in :)

EDIT: My order on yellowjackets.com.au comes to a total of $380 for the coil packs + $40 shipping. Am I meant to buy from the 1st page link to receive the $400 delivered offer?

Edited by BlackLine33

In need of a fresh 6 pack! Just put my order in :)

EDIT: My order on yellowjackets.com.au comes to a total of $380 for the coil packs + $40 shipping. Am I meant to buy from the 1st page link to receive the $400 delivered offer?

Where are you located?




  • Latest Posts

    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
×
×
  • Create New...