Jump to content
SAU Community

Recommended Posts

The SAU forums are definitely a great resource on our cars, thanks to you guys. :thumbsup:

I've had the AFM fail on me once before, on the highway no less. The engine simply cranked out and wouldn't fire up again. I was under the impression the stock turbo had munched itself, and consequently the engine, but the guys at APC here in Brisbane correctly diagnosed it and fitted a new AFM at a good price.

This time round though, I think the reason for the engine misbehaving might have to do with the fact that there's a VQ35DE + stock M35 turbo lurking under the hood. Sorry, I should probably have mentioned that earlier.

The Meisters are from IM. They stick out a fair bit, so the fenders are in the process of getting pulled. I'm hoping the very slight variance in front and rear offsets won't upset the ATTESA system...

Small difference in offset should be OK. Was anything done about the ecu when the +T was done? e.g. ecu from turbo car? If not what are you planning - some kind of pigyback unit?

This time round though, I think the reason for the engine misbehaving might have to do with the fact that there's a VQ35DE + stock M35 turbo lurking under the hood. Sorry, I should probably have mentioned that earlier.

and when abouts had you planned on elaborating about this!

Glad to hear the offsets should be fine, thanks!

It's running on the stock M35 ECU atm, apparently the A/F ratios were spot on.

Been advised I'll need a Motec M800 to get the whole show going since the stock ECU won't play nice with the 35's variable valve timing.

I was driving around everywhere in gears 4 and 5 (Tiptronic), luckily the engine is tractable enough. Other than that there's not much to report, but if you have any q's just ask away biggrin.gif

Glad to hear the offsets should be fine, thanks!

It's running on the stock M35 ECU atm, apparently the A/F ratios were spot on.

Been advised I'll need a Motec M800 to get the whole show going since the stock ECU won't play nice with the 35's variable valve timing.

I was driving around everywhere in gears 4 and 5 (Tiptronic), luckily the engine is tractable enough. Other than that there's not much to report, but if you have any q's just ask away biggrin.gif

Pic's please.....VQ35..........got to see it!

oh....and!!!!

Injectors and E-manage in....only the tune to go tomorrow!

Edited by Jetwreck

This thread is useless without PICS! :stupid::) :)

Are you running the HR? I don't think there's much difference between my non HR hydraulic actuators and the coil actuated retarders on the VQ25det. They are both two wire coils you just need a way of changing the pulse to them.

You need at least some kind of management, how are you adjusting fuel? Emanage would probably do it but you really need standalone management like m800, ps2000, then the dramas will really start. :whistling:

Is the engine built? Fill us all in pleeaaasse. :yes:

I didn't bother taking engine bay pics. It looks almost stock. The only visual differences are some new piping, airbox out and pod filter in, and the intake manifold inlet pipe swapped sides (was on the left before, now it's on the right).

Might take pics if I get half a chance tomorrow.

The engine is internally stock. Is it true the VQ35DE has forged conrods and crank?

I think they are glass not forged. :)

How did you come across this setup? A stock VQ25 turbo is not a good idea on a 3.5L high compression high reving engine period. Imo it is most certainly a downgrade from the VQ25det unless you built it with forged pistons, H beam rods, lower compression and a much larger turbo.

A pic would tell me all I need to know about the engine model.

Just put my new R32 RDA slotted front disks and A1RM's in, now to bed them in. :devil:

you should bed the pads in on the old rotors i believe (or could be the other way round)

there is a thing about it in the diy/tutorial section

I didn't bother taking engine bay pics. It looks almost stock. The only visual differences are some new piping, airbox out and pod filter in, and the intake manifold inlet pipe swapped sides (was on the left before, now it's on the right).

Might take pics if I get half a chance tomorrow.

The engine is internally stock. Is it true the VQ35DE has forged conrods and crank?

Mate....it's a pretty be claim....you would be the first to have a VQ35 in an NM35 in OZ......hence the reason you must post photo's(how hard is it to your phone out and take a shot??

btw......did you say the standard ECU is running it ATM? I can not see how that would work as although the 25 and 35 are from the same family they are still different in a couple of way's that would make me think that more than likely would not work!....e.g. How is the timing controlled at all?...different system's. And why the M800......Haltech PS2000 would be more than good enough at a quarter of the price.

Also you would have had to have the motor nearly apart to change the sump so why would you not have done new rod's and pistons so that it can handle more than 7 to 8psi without throwing a rod out the side one day? Unless of cause it's 2WD now? Or is the motor out of a PM35?

Anyway.....I need you to post up some more info/photo's on this as I am NOT believing you atm!

P.S. I await your photo's and comments so that you can flame mewhistling.gif

Edited by Jetwreck

you should bed the pads in on the old rotors i believe (or could be the other way round)

there is a thing about it in the diy/tutorial section

Yeah, use the old pads to bed the new discs, then throw the new pads in and bed them.

Edited by Daleo

Yeah, use the old pads to bed the new discs, then throw the new pads in and bed them.

too late....his on the way over to see me atm!

I told him just get up to 50-60km's and apply a firm and static brake peddle....the redo about 5 - 10 time's....should be OK then! The guy that sold the bakes said the same thing!

too late....his on the way over to see me atm!

I told him just get up to 50-60km's and apply a firm and static brake peddle....the redo about 5 - 10 time's....should be OK then! The guy that sold the bakes said the same thing!

Meh, don't matter, I've bedded new pads on new discs a bunch of times, never had any issues :whistling:

^^ I knew this too but at the time I changed all my pads and rotors there was no way I was in the mood to do it a second time to change pads later on!!

As for this vq35DE.....T?? I would love to see pics too you can't keep us on edge like this we need a fix!!!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The rain is the best time to push to the edge of the grip limit. Water lubrication reduces the consumption of rubber without reducing the fun. I take pleasure in driving around the outside of numpties in Audis, WRXs, BRZs, etc, because they get all worried in the wet. They warm up faster than the engine oil does.
    • When they're dead cold, and in the wet, they're not very fun. RE003 are alright, they do harden very quickly and turn into literally $50 Pace tyres.
    • Yeah, I thought that Reedy's video was quite good because he compared old and new (as in, well used and quite new) AD09s, with what is generally considered to be the fast Yokohama in this category (ie, sporty road/track tyres) and a tyre that people might be able to use to extend the comparo out into the space of more expensive European tyres, being the Cup 2. No-one would ever agree that the Cup 2 is a poor tyre - many would suggest that it is close to the very top of the category. And, for them all to come out so close to each other, and for the cheaper tyre in the test to do so well against the others, in some cases being even faster, shows that (good, non-linglong) tyres are reaching a plateau in terms of how good they can get, and they're all sitting on that same plateau. Anyway, on the AD08R, AD09, RS4 that I've had on the car in recent years, I've never had a problem in the cold and wet. SA gets down to 0-10°C in winter. Not so often, but it was only 4°C when I got in the car this morning. Once the tyres are warm (ie, after about 2km), you can start to lay into them. I've never aquaplaned or suffered serious off-corner understeer or anything like that in the wet, that I would not have expected to happen with a more normal tyre. I had some RE003s, and they were shit in the dry, shit in the wet, shit everywhere. I would rate the RS4 and AD0x as being more trustworthy in the wet, once the rubber is warm. Bridgestone should be ashamed of the RE003.
    • This is why I gave the disclaimer about how I drive in the wet which I feel is pretty important. I have heard people think RS4's are horrible in the rain, but I have this feeling they must be driving (or attempting to drive) anywhere close to the grip limit. I legitimately drive at the speed limit/below speed the limit 100% of the time in the rain. More than happy to just commute along at 50kmh behind a train of cars in 5th gear etc. I do agree with you with regards to the temp and the 'quality' of the tyre Dose. Most UHP tyres aren't even up to temperature on the road anyway, even when going mad initial D canyon carving. It would be interesting to see a not-up-to-temp UHP tyre compared against a mere... normal...HP tyre at these temperatures. I don't think you're (or me in this case) is actually picking up grip with an RS4/AD09 on the road relative to something like a RE003 because the RS4/AD09 is not up to temp and the RE003 is closer to it's optimal operating window.
    • Either the bearing has been installed backwards OR the gearbox input shaft bearing is loosey goosey.   When in doubt, just put in a Samsonas in.
×
×
  • Create New...