Jump to content
SAU Community

Recommended Posts

Dropped the rear a tad more. Happy to find I could move the circlip on the Bilsteins without removing the shocks but simply jacking up the collar. Also pushed the guards out a bit more. I used to think the "baseball bat is your friend" was a joke but I found I could do more with a bit of steel pipe in 15 minutes than an hour of stuffing round with a guard roller!

Finally got the buttons installed on the steering wheel, look great!

Also go the cruise control wired up, but still need to set it up.

Thanks to Leon for all the help so far - hopefully I don't have to call you again mate!

Fitting a runner spacer on Sunday, very happy with the results. Only drama I had during the install what snapping the head of a bolt but no drama as it was just the bolt that holds the trans filler tube to the plenum. :)

brought some basic stuff. got new spark plugs (ill re-gap), nd fuel filter. will install both along with spitfire coil packs on the weekend. which i have had sitting here for a little while.

and also for those that need diagnostic checks i have put a deposit on a diagnostic scan tool today. which covers most imports. M35 Stageas. skylines, Silvias (only ones i checked). doesn't have the C34 but might be able to look up under skylines.

Which scan tool did you order Michael?

Got my cruise control programmed tonight, very easy really. Leon's instructions are amazing, used Dale's ground wire idea and the Marvey Tech speed wire. Pretty happy with myself!

If I set it the car accelerates quite hard when you hit set, from 80 to 90, as an example. Just have to adjust the gain apparently. Will do this tomorrow then wire up the steering wheel buttons.

I do have an airbag fault light now. Looks like I forgot to push the black clip back in the first time, but it was still in when I pulled it apart again. Fingers crossed it will clear itself now that I've pushed it in, like a CEL.

Thanks to Leon for all his help!

new spark plugs, spitfire coilpacks, nd fuel filter installed. left coil cover off to keep coil packs cool. nd also found on of the connectors for coil pack is broken. so need to try nd find a new loom. nd did final fitting nd cutting of eye lids today. peter just needs to sand back nd create mould. nd should be ready to sell

Fitted our new Turbosmart Dual Port BOV (TS-0205-1026) today and took her for a test flight.

Solved the farting BOV issue which was getting progressively worse which was the reason for grabbing it.

Also appears to have reduced a bit of lag and made the M35 more responsive and feels like it has a bit more fire in the belly according to the Bum Dyno!

Even better was the fact it worked (for my needs) straight out of the box.

Running it in full plumb back mode too.

Fitted our new Turbosmart Dual Port BOV (TS-0205-1026) today and took her for a test flight.

Solved the farting BOV issue which was getting progressively worse which was the reason for grabbing it.

Also appears to have reduced a bit of lag and made the M35 more responsive and feels like it has a bit more fire in the belly according to the Bum Dyno!

Even better was the fact it worked (for my needs) straight out of the box.

Running it in full plumb back mode too.

when it vents anything below 5psi do you get a flutter that pulses through out the whole driveline???

cos thats what mine does and i hate it!!!

What's wrong with factory Bov? I see a lot of you guys change to a/market.

Just block up the recirc whole in the factory unit and they hold a lot more boost. I did this to the factory unit on my 180sx and has held 20psi with no problems. I know of guys running more psi with the stocker.

Edited by slippylotion
What's wrong with factory Bov? I see a lot of you guys change to a/market.

Just block up the recirc whole in the factory unit and they hold a lot more boost. I did this to the factory unit on my 180sx and has held 20psi with no problems. I know of guys running more psi with the stocker.

If the original was working properly (as in not farting and causing the whole car to vibrate, like mine, even under moderate boost), there's no reason to replace it and i would have kept the stock one.

I could have purchased a second hand one and potentially ended up with the same problem or probably spent more (i din't even bother to check TBH) on a new one from Ni$$an.

I purchased the Turbosmart from Mick at BoostnImports for $387 delivered, great guy to deal with and amazingly fast delivery.

Jas

What's wrong with factory Bov? I see a lot of you guys change to a/market.

Just block up the recirc whole in the factory unit and they hold a lot more boost. I did this to the factory unit on my 180sx and has held 20psi with no problems. I know of guys running more psi with the stocker.

Hi Paul, forgot to add, there's a few threads dedicated to this subject too;

http://www.skylinesaustralia.com/forums/topic/327936-m35-bov/

http://www.skylinesaustralia.com/forums/topic/314048-m35-strange-exhaust-noise/

If you don't have the problem though, i wouldn't bother replacing the BOV.

In my case, fixed the issue instantly & i'm as happy as a pig in mud.

^^ this.

If it wasnt playing up I wouldnt have done it. Might have been cheaper to get another stockie, but who knows if that would have the issue too.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • For these last 7 years of ownership, I've always had to use a small scissor jack under one of the front tow hooks to raise the front just enough so my low-profile jack fits under to reach my subframe jack point. I'm beginning to get annoyed of always having to do this. Are there any lower low-profile jacks that fit under the gtr lip on a dropped car?
    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
×
×
  • Create New...