Jump to content
SAU Community

Recommended Posts

  • 3 weeks later...
  • 2 weeks later...
On 5/22/2019 at 5:45 AM, JACKA87 said:

Awesome build mate, just read through it all. Great to see it being done with the goodies and a whole lot of patience! 

cheers mate, the patience has worn thin a few times but I think it's all been worth it :)

 

So a little bit actually happened on this R&R trip home, not all good but not all bad...

I put her on club rego which significantly reduces the cost of registration and insurance here in SA (win, win)...

After a few minor but frustrating teething issues with injector plugs not actually being standard and dramas bleeding the ATTESSA she was finally turned over (boy had i missed that RB sound)...

She was then put on the dyno for a few hours to run her in and do some basic tuning on 98RON. Very happy with the results on pump fuel, just running wastegate pressure (12-13psi) ended up with 279rwkws from memory, video shows the run before at 275rwkws...

Initial feelings from these turbos is impressive, the response is very transient and feels better than what i recall my -7's did...

Whilst out and about putting a few kilometers on her i was thinking to myself she was feeling a little stiff, just put it down to me being a couple years older than when i last drove her but once i got out for the first time i noticed one side was sitting far lower than the other at the rear, after hopping underneath it appeared as though one shock had compressed and not rebounded, so I got her home and pulled the rears out and sure enough this was the case as seen in the below photo ? So now I weigh up whether to rebuild the rears as i did the fronts (really like the feeling the bilsteins give) or I look into some coilovers... The cars driveable so not a huge urgency...

I dropped her off last night before flying back out to site this morning so fingers crossed the 98 tune will be completed along with the E85 over the next 2 weeks... Very excited to see what some E85 in her guts will do :)

IMG_0670.JPG

IMG_0679.JPG

IMG_0710.JPG

IMG_0715.JPG

CZUR4677.JPG

  • Like 3
11 hours ago, Dose Pipe Sutututu said:

Go MCA!!!

This was what I was going to do...

But the guy who I use for tuning and bits & bobs I can't do here in Adelaide said they'd had issues with MCA recently when there was warranty issues, has kinda put me off ?

I had just been reading up about 'The street Essentials' (shows how long it's been since i looked at suspension) they just used to do 'blue', 'red, and 'gold' haha...

2 hours ago, Dose Pipe Sutututu said:

Yeah they've increased their range to meet market needs, but I feel now they've done that the distinction between the lines are blurred.

 

yup, exactly what I was thinking whilst perusing their site this morning ??

2 hours ago, Dose Pipe Sutututu said:

They still get it so right though, I run MCA X-R (not sure what they're equivalent to now) with 10/7 spring rates and they feel less harsh than a set of BC BR 8/6

I don't mind the idea of the 'street essentials' in stealth black...

 

7 minutes ago, MBS206 said:

I'm a fan of blistein, and if they were well sorted and it drove nicely, why chance it? 

finding someone who will rebuild them is the only thing stopping that from happening...

here in oz it appears everything these days is throw away and replace (boy i sound old saying that) ?

Edited by mr_rbman
  • Haha 1
4 minutes ago, mr_rbman said:

finding someone who will rebuild them is the only thing stopping that from happening...

here in oz it appears everything these days is throw away and replace (boy i sound old saying that) ?

Wasn't white line rebuilding them at least back in the day?

15 hours ago, MBS206 said:

Wasn't white line rebuilding them at least back in the day?

got an email back from Bilstein Australia themselves who actually appear to have bought Quadrant suspensions (in Victoria) so may have a solution, they are calling me back tomorrow.

 

  • Like 1
  • 2 weeks later...

Just got word from the tuner it is currently making 323rwkws @16-17psi... on 98RON

Fuel pump appears to possibly be an issue (Walbro 460) getting very warm... Looking into it further now...

  • 3 weeks later...

Well I think I can say I pretty much achieved what I set out to more than 2 years back...

I've got myself a NisTune cable so will try and get some logging done on my next R&R to show the rather impressive response achieved (as they dyno graphs obviously don't show it) given I was set on staying low mount twins. I know I could've achieved so much more with a modern single but I do honestly feel far less disappointed than I had expected to...

Finally got round to fitting the correct boot badges as well...

IMG_0772.JPG

IMG_0795.JPG

IMG_0796.JPG

IMG_0799.JPG

IMG_0800.JPG

IMG_E0766.JPG

IMG_E0767.JPG

  • Like 3

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • There's plenty of OEM steering arms that are bolted on. Not in the same fashion/orientation as that one, to be sure, but still. Examples of what I'm thinking of would use holes like the ones that have the downward facing studs on the GTR uprights (down the bottom end, under the driveshaft opening, near the lower balljoint) and bolt a steering arm on using only 2 bolts that would be somewhat similarly in shear as these you're complainig about. I reckon old Holdens did that, and I've never seen a broken one of those.
    • Let's be honest, most of the people designing parts like the above, aren't engineers. Sometimes they come from disciplines that gives them more qualitative feel for design than quantitive, however, plenty of them have just picked up a license to Fusion and started making things. And that's the honest part about the majority of these guys making parts like that, they don't have huge R&D teams and heaps of time or experience working out the numbers on it. Shit, most smaller teams that do have real engineers still roll with "yeah, it should be okay, and does the job, let's make them and just see"...   The smaller guys like KiwiCNC, aren't the likes of Bosch etc with proper engineering procedures, and oversights, and sign off. As such, it's why they can produce a product to market a lot quicker, but it always comes back to, question it all.   I'm still not a fan of that bolt on piece. Why not just machine it all in one go? With the right design it's possible. The only reason I can see is if they want different heights/length for the tie rod to bolt to. And if they have the cncs themselves,they can easily offer that exact feature, and just machine it all in one go. 
    • The roof is wrapped
    • This is how I last did this when I had a master cylinder fail and introduce air. Bleed before first stage, go oh shit through first stage, bleed at end of first stage, go oh shit through second stage, bleed at end of second stage, go oh shit through third stage, bleed at end of third stage, go oh shit through fourth stage, bleed at lunch, go oh shit through fifth stage, bleed at end of fifth stage, go oh shit through sixth stage....you get the idea. It did come good in the end. My Topdon scan tool can bleed the HY51 and V37, but it doesn't have a consult connector and I don't have an R34 to check that on. I think finding a tool in an Australian workshop other than Nissan that can bleed an R34 will be like rocking horse poo. No way will a generic ODB tool do it.
    • Hmm. Perhaps not the same engineers. The OE Nissan engineers did not forsee a future with spacers pushing the tie rod force application further away from the steering arm and creating that torque. The failures are happening since the advent of those things, and some 30 years after they designed the uprights. So latent casting deficiencies, 30+ yrs of wear and tear, + unexpected usage could quite easily = unforeseen failure. Meanwhile, the engineers who are designing the billet CNC or fabricated uprights are also designing, for the same parts makers, the correction tie rod ends. And they are designing and building these with motorsport (or, at the very least, the meth addled antics of drifters) in mind. So I would hope (in fact, I would expect) that their design work included the offset of that steering force. Doesn't mean that it is not totally valid to ask the question of them, before committing $$.
×
×
  • Create New...