Jump to content
SAU Community

R34 GTT Rebuild - Manifold/Turbo Advice


macca911
 Share

Recommended Posts

2 hours ago, Dose Pipe Sutututu said:

^ yep!

then buy proper tyres, a proper LSD, proper suspension arms to fix up the crappy Nissan rear geometry.. If you can't even put 200kW down to the ground, don't bother with power upgrades.

But if you're single pegging everywhere, who cares brah! 300kW uleh.

  • Like 1
Link to comment
Share on other sites

On 9/16/2016 at 10:50 AM, Dose Pipe Sutututu said:

^ yep!

then buy proper tyres, a proper LSD, proper suspension arms to fix up the crappy Nissan rear geometry.. If you can't even put 200kW down to the ground, don't bother with power upgrades.

The later model 34 GTTs have a Helical Diff yea? Is it worth the upgrade providing this is in a healthy condition? 
I do plan to take her to the track, I'm assuming a true 1.5 way would be better... 

Edited by macca911
Link to comment
Share on other sites

For street, a helical is pretty much the nicest diff.

For track, a proper mechanical diff is better.  Especially if you have really high roll stiffness - where you may lift the inside rear wheel off the ground - or if you tend to hit kerbs hard enough to do the same.  Getting a wheel up instantly converts a helical into an open diff.

Also S2 R34 helical diffs are like hen's teeth and if you find one I would prefer you let me buy it.  Or at least the 5 bolt stub axles from it!

Edited by GTSBoy
Link to comment
Share on other sites

On 9/16/2016 at 1:53 AM, hypergear said:

lets say. I can get you 3582's power with better then 3076's response. and much cheaper in price.

Hypergear, I'm listening... Would this be something like the Atr45sat?
Internal or external gate? 

Cheers,  

Link to comment
Share on other sites

Thats the latest ATR45SAT RV2 model in ceramic ball bearing center. Is maxed at 330rwkws on 22psi p98 fuel internally gated Bolton, 20psi by 3650rpm, unopened neo motor.  Run that externally gated e85 it will be making around 400rwkws region. Check my fb or dyno sheet section for result.

  • Like 3
Link to comment
Share on other sites

  • 1 year later...

Gents,

It's been some time since my last post. 
The car has been finished and it made a super responsive 625rwhp and 680nm (e85)

I went with the following setup: 

  • JHH Built RB25 Neo 
  • EFR BW 7670 1.05 TS
  • 6boost Manifold with twin gates.
  • 2000cc Bosch Injectors
  • Haltech Platinum Pro
  • Hypertune Plenum + TB 
  • PWR Intercooler and Oil Cooler

I can't recommend GT Auto Garage at Slacks Creek enough.
Their attention to detail in both fabrication and tuning is fantastic!  

Still running the stock gearbox...

 

Cheers, 

  • Like 3
Link to comment
Share on other sites

It turns out every car I drove after mine felt like an absolute dog.

The EFR smashes the GTX3071 in every aspect.

I have unrealistic expectations for response it would appear relative to 100% of RB's ever built. I would assume that a 2.5 with a 7670 would be laggy, or at least laggier than mine. Still going to be better than anything else bolted to a 2.5.

The result does backup my thinking on the matter, that the 7670 is actually a pretty big turbo and is more a 450kw turbo than a 350kw turbo that people seem to consider it to be. Would be curious to see if there is speed sensor data as 466rwkw is really up there.

Link to comment
Share on other sites

On 7/3/2018 at 12:04 PM, macca911 said:

Gents,

It's been some time since my last post. 
The car has been finished and it made a super responsive 625rwhp and 680nm (e85)

I went with the following setup: 

  • JHH Built RB25 Neo 
  • EFR BW 7670 1.05 TS
  • 6boost Manifold with twin gates.
  • 2000cc Bosch Injectors
  • Haltech Platinum Pro
  • Hypertune Plenum + TB 
  • PWR Intercooler and Oil Cooler

I can't recommend GT Auto Garage at Slacks Creek enough.
Their attention to detail in both fabrication and tuning is fantastic!  

Still running the stock gearbox...

 

Cheers, 

Very nice!  Can you please share the dyno plot?  The peak power is solid, but not the most interesting part of that setup :)

Link to comment
Share on other sites

Kinkstaah Unfortunately I don't have a speed sensor installed. It's coming... 
I have to agree, it must be pushing the limits!! 

KiwiRS4TIt wasn't intentional... I've now got concerns for the gearbox etc... Matter of time haha.  

E85 run attached. I believe the dip at 5400 would be VVT... Please correct me if I'm wrong. 
Unfortunately, I'm in the US and only have the 625hp/640nm run photo on me. You'll get the idea though.
The final power run video is on the GT Auto FB page. 

As always, bugs to iron out and more mods to do.
At this stage, I've planned as far as brakes and an accusump setup in the coming weeks... 

 

IMG_5005.JPG

33092266_10156193311026399_823423248724131840_n.jpg

  • Like 1
Link to comment
Share on other sites

52 minutes ago, macca911 said:

E85 run attached. I believe the dip at 5400 would be VVT... Please correct me if I'm wrong. 
Unfortunately, I'm in the US and only have the 625hp/640nm run photo on me. You'll get the idea though.
The final power run video is on the GT Auto FB page. 

As always, bugs to iron out and more mods to do.
At this stage, I've planned as far as brakes and an accusump setup in the coming weeks... 

The dyno run attached does look quite a bit like it could be VVT turning off too early, I'm assuming that's sorted now?   

Saw a post on NZ Wiring's workshop page of a very similar setup/workshop which upgraded to an NZ Wiring CAS setup on an RB25 Neo recently, wasn't you by any chance?  Very solid delivery for an RB25 making that kind of power, though.  Should be a fun drive :)

  • Like 1
Link to comment
Share on other sites

6 minutes ago, Lithium said:

The dyno run attached does look quite a bit like it could be VVT turning off too early, I'm assuming that's sorted now?   

Saw a post on NZ Wiring's workshop page of a very similar setup/workshop which upgraded to an NZ Wiring CAS setup on an RB25 Neo recently, wasn't you by any chance?  Very solid delivery for an RB25 making that kind of power, though.  Should be a fun drive :)

Nah, not me. I'll take a look though! 
Not sorted yet... Mainly due to work commitments. I'll aim to spend some time on it starting next week.

Edited by macca911
Link to comment
Share on other sites

3 minutes ago, macca911 said:

Nah, not me. I'll take a look though! 
Not sorted yet... Mainly due to work commitments. I'll aim to spend some time on it starting next week.

(y) This is the post that got my attention btw: https://www.facebook.com/nzwiring/photos/a.263208990533912.1073741827.263205613867583/915378341983637/?type=3&theater

  • Like 1
Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share




  • Similar Content

  • Latest Posts

    • Go to SP mufflers and get the muffler of size you want and make a nice mid muffler. It's about that simple! I have 2x 3.5 Magnaflow straight through Mufflers and while it's pretty loud with the Varex open, it's quiet enough with the Varex closed. You can also buy off the shelf Magnaflow straight through mufflers as well. You also have a turbo to quiet the car down too. Don't overthink it. Buy my extra Magnaflow muffler sitting on a shelf doing nothing (buy it new, ignore this part)
    • Centre-offset muffler under the floor, same as stock. Just....3.5". The change from straight pipe there to centre-offset will mean that you need to remake some of the pipe (add a bend or two).
    • Hey guys. So my R34 GTT has a custom 3.5” exhaust (done by previous owner) with a high flowing cat, and then just a Varex cannon muffler on the back. The car does drone alot and is really loud even on highway driving just cruising, as you can imagine due to the Varex muffler basically being a straight through with the valve open. As much as i love a loud RB, it can be a bit much with no other muffling in line and just driving casually. I wanted to lower the volume output on the exhaust a bit, as well as remove the drone (probably a way to do both at once), and was going to do it all myself as I am a fabricator and have done exhaust work in the past, so the fab work isnt my issue, im just not sure on the right product or type of product to use to get the job done, and i doubt an exhaust shop would be wanting to help me as they wont be making any money from helping me, unless they supplied the product? Anyway any help or guidance in best way to approach this would be awesome   Thanks in advance
    • Meh, whilst the Honda is a "really" good car and has potential if you want to drop coin on, it was uninspiring for me to look at, but, it did serve its purpose and is now in the boys hands, his happy, his girl is happy, as she wasn't to keen on the noisy old Patrol, and most importantly, the Minister for War and Finances is extremely happy that her "little baby boy" (6'2 nugget who is currently training to be a copper, which will make 3 coppers in the immediate "circle of trust") has a well sorted reliable car that doesn't guzzle diesel Me, I'm more than happy with the NC MX5 that I replaced it with, it's a fun little car that I like looking at, like driving, and yes..... I do like the fact that the maintenance and modifications that I have done/will do are plentiful and relatively cheap, well........ while staying naturally aspirated slow that is, and that's all I really need for a fun little daily, I can rev the 5hit out of it rowing through the gears and never really break the speed limit  In saying that wicked word, "modifications", I've already ordered something for some noise and an additional "3 ish" horse powers, or whatever it gives, in the form of a header, and, a new set of "cheapo" BC coilovers that are already sitting in the shed waiting to get put in, I had the same BC's in my old NB and found they were fine for the street, hwy, and the occasional track days I did in it, they have 6kg front and 4kg rear springs which is about 10% stiffer than the stock springs which I found worked well for their price  I've also already been in touch with MX5 Mania in Dural, so once the header is on it will get a ECUTek RaceROM tune there (I cannot rev match for 5hit, and I loved the RaceROM rev match and FFS in my old 86 "RIP") In other, maintenance news, I put some new sparkler plugs in it, and have a new set of DBA Street series pads to put in over the next day or so, I'm running the DBA street series in the SS and Honda and really like them, they work great and are not dusty at all I've also booked in a few days leave over this weekend to give me 4 days weekend do some paint correction and give the leather seats some conditioning and interior some Bissell and steam cleaning OCD lovin', the carpet and interior looks clean, but from my experience with the Bissell IRT carpet, and the steam cleaner IRT trim, looks can be deceiving I've also found that finding a detachable hard top is proving problematic, the main reason why I didn't like the NC initially was the power retractable hard top that I seen them with gave the roof line a weird look, the detachable roof though looks good, and is a same shape as a NA/NB hard top, similar, but unfortunately not the same as it has different fixture point on the front, so fitting a easy to get NA/NB detachable hard top is no bueno New Old cars are fun, cleaning, hunting and playing around brings much joy How are your beasties going? Do you still have the Skyline with the LS???, or Barra??? that you were playing with
×
×
  • Create New...