Jump to content
SAU Community

Recommended Posts

G30 turbine flow :

Les turbo garrett G series - Page 4 G30turbineflowmap

 

G35 turbine flow :

Les turbo garrett G series - Page 4 G35turbineflowmap

The compressor flow chart :

 

770 :

Les turbo garrett G series - Page 4 G30-770comp-map

 

The 900 one :

Les turbo garrett G series - Page 4 G35-900comp-map

 

and finally the 1050 one :

 

Les turbo garrett G series - Page 4 G35-1050comp-map

All were taken from ATP website so I consider these as legit but still take these with a grain of salt as they were not officially released.

6 hours ago, R_34 said:

 

All were taken from ATP website so I consider these as legit but still take these with a grain of salt as they were not officially released.

Understood, and very much appreciated - thanks for sharing - that's awesome.

I'm pretty confident they are legit, btw.  Just probably weren't meant to be released yet

I've had a quick play with that data, and if I am looking at it right - the 1.01a/r G30 hotside is very comparable to the 1.05a/r EFR8374 hotside which puts things into perspective.


The .83a/r G30 hotside falls slightly short of the .82a/r GT35 hotside in flow.   I think Garrett have chosen some very nice spread of options with this range.

  • 4 weeks later...
On 12/04/2019 at 4:41 PM, Phat_Toni said:

The g25 660 with the 0.92 looks comparable to the GT3076r but seems to have the edge in turbine flow, compressor flow and spool. 

g25 660 0.92 from ATS 

6boost mani

 

I saw a post on Sinco NZ's Instagram page which made me think of you, how is your build going?  Did you end up going Sinco for the manifold or is there someone else doing similar?

image.png.676e27afa0879be80102e5c2f3a98f37.png

1 hour ago, Skylineusa said:

This page is gold with great information. Thank you guys! Would running twin 550 be a worthwhile combo? 

That's a very open ended question.  For what power target and on what kind of setup??  Do you have the budget and inclination to do all the fabrication to do twin 550s? (it's not something you'd do on stock manifolds/location). 

It is the kind of setup which to justify would need a pretty solid engine spec, basically its a 1000hp turbo setup so expect the kind of lag that would come with one and expect to need to do the kind of engine and transmission development needed to support it.   If you are looking at making the typical kind of power that people go for with low mount twins then no, imho it is not worth doing.

5 minutes ago, Phat_Toni said:

I think this car was mentioned earlier in the thread. Gives a good idea as what to expect from 2 of these things....

 

It's worth nothing a couple of things he says which contradict each other, he implies it spools 500rpm better than the EFR9180 but then also says its all in between 6000-7000rpm which on a 2.8 is... umm... much laggier than any EFR9180 I've heard of.

It's been previously said that it's got a 500rpm wider powerband as the 660s hold on (unsurprisingly) to much higher rpm than the EFR9180 and other turbo setups they ran on it, so if you are willing to rev it to 9000+rpm then it offers the potential to give a broad delivery - as long as you aren't hoping for things to happen earlier in the rev range.

Be great to get some more data points from that car.  

 

The twin G25-550 intrigues me as well.  They do the internal gate T2 .49 which screams bolt me on an RB26.

I've be told by a seller its not a bolt on affair though. I was not given any details other than you have a 30 year old car "dude" as to why. 

The cost of them makes it a serious investment and a risk you end up with a street pig.

If not and they make 900-1000fwhp with amazing spool  ..... all the glory is yours  ......

 

When they released the spec sheet on the g25 I looked at them real hard. The problem I saw is they are longer than the stock turbo. There just doesn't seem to be horizontal room for them. Granted this is based off the spec sheet and not trial and error.

If we could slant them 20° from horizontal they might fit but you can't do that and expect the snail to live.

Sorry Lithium, you are correct. I should have gone into a little more detail. I was thinking for quick spool, which I understand by your reply, and looking at the map, would not be a good marriage. It looks like I will wait for the 770s to come out, and go that route.

Hypertune makes twin manifolds for the G25s, if anyone is going that route. My car is more street than track, so I really do not need that much power.

 

Edited by Skylineusa
9 hours ago, Skylineusa said:

It looks like I will wait for the 770s to come out, and go that route.

Hypertune makes twin manifolds for the G25s, if anyone is going that route. My car is more street than track, so I really do not need that much power.

I hope you mean a single 770? :o

  • Haha 1

Yeh its interesting.  

I am in the process of getting rid of my HKS F-con rubbish in favour of a Link g4+ and upgrading my trigger system and fuel system at the same time.

Once done the G30-770 be on the next list to replace the -5's.

So sooner they come out the better so someone else test for me.

  • Like 3

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Yeah good luck out there! Will be good to see a mighty GTST going harder than the GTRs
    • i will be there 😁
    • Hello!  i just finished manual swaping my r34 skyline with a r33 rb20de box(RB71C)box  When the car is running it squeaks crazy loud and it was smoking from the gearbox area. The gearbox is fine it was tested. The clutch slave cylinder seems like it doesn't fully releases the clutch. I want to ask if this noise is from the throw out bearing or could it be the clutch assembly or disk att.xFliq87Gzw6kImKBVqDebXkj0fBqymk0JaYeP3_3SlM.mp4
    • A few small updates since the previous post and lessons. I decided to do a little interior light upgrade on the 110. I quite like the iilumo items, even if they're a bit of a premium over other brands. You'll also note the Stedi Fogs, that will go into the S15 fog lights as I needed to match the bulbs since I got the new ones earlier. I hope they fit as the body is quite a bit longer than your normal bulb.  Annoyingly, I managed to trip the fuse, which normally wouldn't be an issue until I located the fuse. I can't say I've ever come across this. I had lucked out that someone nearby had a spare, but oddly enough Toyota dealerships seem to keep this in stock. I ordered some to keep in my stash and as luck would have it, someone else nearby tripped the same fuse so I passed on the favour.  I also did a little service on the 110 ahead of some additional work coming up. It's been annoying that Goleby's stopped carrying this particular HKS filter for the 110, so now I need to keep them on order from Japan. I also took the opportunity to install a bash plate and number plate riser. The plate riser is such a cheap but nice fix to help really tidy up the car. I'm tempted to now also replace my headlights, on this car. Both items were from Project Aero.    I also needed to replace the rear tyres on the 110, and after trying to get it aligned learnt that I need to replace some bushes in the front end, so that's next.  Closing out this update with a nicer picture as always! 
    • Yeah mate, never miss it.
×
×
  • Create New...