Jump to content
SAU Community

Recommended Posts

That one works fine cheers mate! That BOV would be getting very hot without heat shielding I imagine, did he go to a full race metal cover? I hadn't heard any mention of the noise these things made either until Greg mentioned it. Hopefully the 6758 is just as noisy but it has the type a front which isn't anti-surged and only 2.5" inlet.

4 hours ago, rb30det_ said:

Has anyone here run a EFR 9174 or 9180 1.05Ar on a RB30 or Stroker??  Looking at running a Borgy on a 26/3.4. But cannot decide .. Looking to see what would work best in a drift car

 

for a 3L or 3.4L the single EFR will choke.  Twin EFR is my recommendation.

2 hours ago, R_34 said:

What is the boost target ?  If lower than 25psi on a 3.4L go 9180 1.05 a/r.  If higher than that go 9174 1.45 as the compressor will spin close to the max rpm the 80mm turbine can take.

both of those options will likely choke due to backpressure on a 3.4L engine

7 hours ago, Lithium said:

Weird, ok this then

594200a32fa81_EFR7064stand.thumb.png.e8783a0ea74a4cac679c4e6bea9cd81a.png

some more photos of similar

 

 

rb25-t3-b2efr.jpg

rb25-t3-b2efr-1.jpg

rb25-t3-b2efr-2.jpg

unnamed.jpg

  • Like 2
4 hours ago, rb30det_ said:

Has anyone here run a EFR 9174 or 9180 1.05Ar on a RB30 or Stroker??  Looking at running a Borgy on a 26/3.4. But cannot decide .. Looking to see what would work best in a drift car :)

 

Long thread but 8374 on 3.2 results towards the end

27 minutes ago, Full-Race Geoff said:

for a 3L or 3.4L the single EFR will choke.  Twin EFR is my recommendation.

both of those options will likely choke due to backpressure on a 3.4L engine.

 

 

 

Ever taken any EGP readings on combo's like this, Geoff?

 

4 hours ago, rb30det_ said:

Has anyone here run a EFR 9174 or 9180 1.05Ar on a RB30 or Stroker??  Looking at running a Borgy on a 26/3.4. But cannot decide .. Looking to see what would work best in a drift car :)

 

Page 26 on this thread has my result on a 26/3.2 EFR8374

Tune #1 done, I was a bit concerned about this happening but it is what it is - the BW EFR internal wastegate is a big pile of fail and blows open as exhaust pressure builds.  The turbo itself seems to perform awesome, VE is holding nicely up to 7000rpm so far and no hints of excess back pressure, intake temps never reached 30C... I'm going to try and get video of the gate opening as rpm increase despite having 80% duty on the boost control solenoid.

256kw at 14psi, hitting 18psi by 3500rpm - will be revisited at some point with a Turbosmart dual port actuator.  Car drives basically like a Euro, it spools better on the road than my Mazdaspeed 3 with the stock K04 :O

 

 

EFR7064 Boost.jpg

EFR7064 Power.jpg

  • Like 2
13 hours ago, Lithium said:

Tune #1 done, I was a bit concerned about this happening but it is what it is - the BW EFR internal wastegate is a big pile of fail and blows open as exhaust pressure builds.  The turbo itself seems to perform awesome, VE is holding nicely up to 7000rpm so far and no hints of excess back pressure, intake temps never reached 30C... I'm going to try and get video of the gate opening as rpm increase despite having 80% duty on the boost control solenoid.

256kw at 14psi, hitting 18psi by 3500rpm - will be revisited at some point with a Turbosmart dual port actuator.  Car drives basically like a Euro, it spools better on the road than my Mazdaspeed 3 with the stock K04

 

In case folks hadn't been following, the above is a T3 0.83 internally gated EFR7064 on an RB25 - btw.

A helpful mate has offered use of his high pressure BW actuator to test out on this car to make sure that fixes it before buying things, thanks @Sub Boy32!    Hoping that it allows us to hold around 18-19psi, or whatever it seems appropriate to run :)

  • Like 3

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • A few small updates since the previous post and lessons. I decided to do a little interior light upgrade on the 110. I quite like the iilumo items, even if they're a bit of a premium over other brands. You'll also note the Stedi Fogs, that will go into the S15 fog lights as I needed to match the bulbs since I got the new ones earlier. I hope they fit as the body is quite a bit longer than your normal bulb.  Annoyingly, I managed to trip the fuse, which normally wouldn't be an issue until I located the fuse. I can't say I've ever come across this. I had lucked out that someone nearby had a spare, but oddly enough Toyota dealerships seem to keep this in stock. I ordered some to keep in my stash and as luck would have it, someone else nearby tripped the same fuse so I passed on the favour.  I also did a little service on the 110 ahead of some additional work coming up. It's been annoying that Goleby's stopped carrying this particular HKS filter for the 110, so now I need to keep them on order from Japan. I also took the opportunity to install a bash plate and number plate riser. The plate riser is such a cheap but nice fix to help really tidy up the car. I'm tempted to now also replace my headlights, on this car. Both items were from Project Aero.    I also needed to replace the rear tyres on the 110, and after trying to get it aligned learnt that I need to replace some bushes in the front end, so that's next.  Closing out this update with a nicer picture as always! 
    • Yeah mate, never miss it.
    • Any going to watch World Time Attack at SMSP this year?
    • Appreciate the correction on the "ground", that will make a huge difference to looking at this. That makes complete sense about AF70/AF71 which is what I had come down to being the issue, one of these. I'll have another look in the ignition wiring when I get a chance next week. I'll also make up a jumper wire for running that AF73 test.  ECU is fine, relay itself is fine, pump harness is fine and the pump itself is fine. I am going to upgrade the Walbro 255 anyway with a DW300 I have since I need to replace the fuel sender and I'm going to upgrade the FPR with my chasebays kit ready for new plenum/injectors/dbw, but I'll get this working first. That's why this is so frustrating. 
×
×
  • Create New...